diff --git a/tcl/board/glyn_tonga2.cfg b/tcl/board/glyn_tonga2.cfg
new file mode 100644
index 000000000..783ef9fa4
--- /dev/null
+++ b/tcl/board/glyn_tonga2.cfg
@@ -0,0 +1,170 @@
+#
+# Glyn Tonga2 SO-DIMM CPU module (Toshiba TMPA900CMXBG, ARM9)
+#
+# http://toshiba-mikrocontroller.de/sites/TMPA900CPUBOARDStarter.htm
+#
+# Hardware on the S0-DIMM module:
+#   - Toshiba TMPA900CMXBG (ARM9, ARM926EJ-S, max. 200MHz)
+#   - DDR SDRAM: Hynix H5MS5162DFR-J3M (64Mbyte, x16, 1.8V, 166/83MHz at CL3/2)
+#   - NAND flash: Samsung K9F2G08U0B-PIB0 (256M x 8 Bit, 3.3V)
+#   - Ethernet: SMSC LAN9221I-ABZJ (10/100Mbit, Non-PCI, 16 bit interface)
+#
+
+source [find target/tmpa900.cfg]
+
+########################
+# Target configuration #
+########################
+
+$_TARGETNAME configure -event reset-init { tonga2_init }
+
+proc tonga2_init { } {
+
+	######################
+	# PLL initialization #
+	######################
+
+	# Clock overview (see datasheet chapter 3.5.2, page 57):
+	#   - fs: Low-frequency oscillator
+	#   - fOSCH: High-frequency oscillator (24MHz on this board)
+	#   - fPLL = fOSCH * multiplier (where multiplier can be 6 or 8)
+	#   - fFCLK = fPLL / gear (where gear can be 1/2/4/8)
+	#   - fHCLK is always fFCLK/2. fPCLK is also fFCLK/2.
+	#
+	# We select multiplier = 8 and gear = 1, so
+	#   fFCLK = fOSCH * 8 / 1 = 192MHz.
+
+	# SYSCR3 (System Control Register 3): Disable and configure PLL.
+	#   - PLL operation control: off
+	#   - PLL constant value setting 1: always 0, as per datasheet
+	#   - PLL constant value setting 2: x8 (multiplier = 8)
+	mww 0xf005000c 0x00000007
+
+	# SYSCR4 (System Control Register 4): Configure PLL.
+	#   - PLL constant value setting 3: 140MHz or more
+	#   - PLL constant value setting 4: always 1, as per datasheet
+	#   - PLL constant value setting 5: 140MHz or more
+	mww 0xf0050010 0x00000065
+
+	# SYSCR3 (System Control Register 3): Enable PLL.
+	#   - PLL operation control: on
+	#   - All other bits remain set as above.
+	mww 0xf005000c 0x00000087
+
+	# Wait for PLL to stabilize.
+	sleep 10
+
+	# SYSCR2 (System Control Register 2): Switch from fOSCH to fPLL.
+	#   - Selection of the PLL output clock: fPLL
+	mww 0xf0050008 0x00000002
+
+	# SYSCR1 (System Control Register 1):
+	#   - Clock gear programming: fc/1 (i.e., gear = 1, don't divide).
+	mww 0xf0050004 0x00000000
+
+	# CLKCR5 (Clock Control Register 5): Set bits 3 and 6. The datasheet
+	# says the bits are reserved, but also recommends "Write as one".
+	mww 0xf0050054 0x00000048
+
+
+	##############################################################
+	# Dynamic Memory Controller (DMC) / DDR SDRAM initialization #
+	##############################################################
+
+	# PMC (Power Management Controller):
+	# PMCDRV (External Port "Driverbility" control register):
+	# Bits DRV_MEM0/DRV_MEM1 (memory relation port drive power):
+	mww 0xf0020260 0x00000003	;# Select 1.8V +/- 0.1V
+
+	# Setup DDR SDRAM timing parameters for our specific chip.
+	mww 0xf4310014 0x00000004	;# cas_latency = 2
+	mww 0xf4310018 0x00000001	;# t_dqss = 1
+	mww 0xf431001c 0x00000002	;# t_mrd = 2
+	mww 0xf4310020 0x0000000a	;# t_ras = 10
+	mww 0xf4310024 0x0000000a	;# t_rc = 10
+	mww 0xf4310028 0x00000013	;# t_rcd = 3, schedule_rcd = 2
+	mww 0xf431002c 0x0000010a	;# t_rfc = 10, schedule_rfc = 8
+	mww 0xf4310030 0x00000013	;# t_rp = 3, schedule_rp = 2
+	mww 0xf4310034 0x00000002	;# t_rrd = 2
+	mww 0xf4310038 0x00000002	;# t_wr = 2
+	mww 0xf431003c 0x00000001	;# t_wtr = 1
+	mww 0xf4310040 0x0000000a	;# t_xp = 10
+	mww 0xf4310044 0x0000000c	;# t_xsr = 12
+	mww 0xf4310048 0x00000014	;# t_esr = 20
+
+	# dmc_memory_cfg_5 (DMC Memory Configuration register):
+	# Set memory configuration:
+	# column_bits = 10, row_bits = 13, ap-bit = 10, power_down_prd = 0,
+	# auto_power_down = disable, stop_mem_clock = disable, memory_burst = 4
+	mww 0xf431000c 0x00010012
+
+	# dmc_user_config_5 (DMC user_config register):
+	# Data bus width of DDR SDRAM: 16 bit
+	mww 0xf4310304 0x00000058
+
+	# dmc_refresh_prd_5 (DMC Refresh Period register):
+	# Auto refresh: every 2656 (0xa60) DMCSCLK periods.
+	mww 0xf4310010 0x00000a60
+
+	# dmc_chip_0_cfg_5 (DMC chip_0_cfg registers):
+	#   - SDRAM address structure: bank, row, column
+	#   - address_match = 01000000 (start address [31:24])
+	#   - address_mask  = 11111100 (start address [31:24] mask value)
+	mww 0xf4310200 0x000140fc
+
+	# Initialize the DDR SDRAM chip.
+	# dmc_direct_cmd_5 (DMC Direct Command register).
+	# See datasheet chapter 3.10.5.1, page 268.
+	mww 0xf4310008 0x000c0000	;# RAM init: NOP
+	mww 0xf4310008 0x00000000	;# RAM init: Precharge all
+	mww 0xf4310008 0x00040000	;# RAM init: Autorefresh
+	mww 0xf4310008 0x00040000	;# RAM init: Autorefresh
+	mww 0xf4310008 0x00080032	;# RAM init: addr_13_to_0 = 0x32
+	mww 0xf4310008 0x000c0000	;# RAM init: NOP
+	mww 0xf4310008 0x000a0000	;# RAM init: bank_addr = bank 2
+
+	# dmc_id_<0-5>_cfg_5 (DMC id_<0-5>_cfg registers):
+	# Set min./max. QoS values.
+	#   - 0x5: Enable QoS, max. QoS = 1
+	#   - 0xb: Enable QoS, min. QoS = 2
+	mww 0xf4310100 0x00000005	;# AHB0: CPU Data
+	mww 0xf4310104 0x00000005	;# AHB1: CPU Inst
+	mww 0xf4310108 0x0000000b	;# AHB2: LCDC
+	mww 0xf431010c 0x00000005	;# AHB3: LCDDA, USB
+	mww 0xf4310110 0x00000005	;# AHB4: DMA1
+	mww 0xf4310114 0x00000005	;# AHB5: DMA2
+
+	# dmc_memc_cmd_5 (DMC Memory Controller Command register):
+	# Change DMC state to ready.
+	mww 0xf4310004 0x00000000	;# memc_cmd = "Go"
+
+	# EBI: SMC Timeout register
+	mww 0xf00a0050 0x00000001	;# smc_timeout = 1
+
+
+	########################################################
+	# Static Memory Controller (SMC) / SRAM initialization #
+	########################################################
+
+	# smc_set_cycles_5 (SMC Set Cycles register):
+	# tRC = 10, tWC = 10, tCEOE = 7, tWP = 5, tPC=2, tTR=2
+	mww 0xf4311014 0x0004afaa
+
+	# smc_set_opmode_5 (SMC Set Opmode register):
+	# Memory data bus width = 16 bits, async read mode, read burst
+	# length = 1 beat, async write mode, write burst length = 1 beat,
+	# byte enable (SMCBE0-1) timing = SMCCSn timing, memory burst boundary
+	# split setting = burst can cross any address boundary
+	mww 0xf4311018 0x00000001
+
+	# smc_direct_cmd_5 (SMC Direct Command register):
+	# cmd_type = UpdateRegs, chip_select = CS1
+	mww 0xf4311010 0x00c00000
+}
+
+#######################
+# Flash configuration #
+#######################
+
+# TODO: Implement NAND support.
+