ULINK driver: Remove typedefs in OpenULINK firmware: Use typedefs from stdint.h (uint8_t, uint16_t) instead of custom typedefs in shorttypes.h (u8, u16, ...)

Signed-off-by: Martin Schmölzer <martin.schmoelzer@student.tuwien.ac.at>

src/jtag/drivers/OpenULINK/Makefile

@@ -61,8 +61,7 @@ HEADERS = $(INCLUDE_DIR)/main.h         \
           $(INCLUDE_DIR)/delay.h        \
           $(INCLUDE_DIR)/reg_ezusb.h    \
           $(INCLUDE_DIR)/io.h           \
-          $(INCLUDE_DIR)/msgtypes.h     \
+          $(INCLUDE_DIR)/msgtypes.h
-          $(INCLUDE_DIR)/shorttypes.h
 
 # Disable all built-in rules.
 .SUFFIXES:

src/jtag/drivers/OpenULINK/include/delay.h

@@ -21,14 +21,14 @@
 #ifndef __DELAY_H
 #define __DELAY_H
 
-#include "shorttypes.h"
+#include <stdint.h>
 
 #define NOP  {__asm nop __endasm;}
 
 void delay_5us(void);
 void delay_1ms(void);
 
-void delay_us(u16 delay);
+void delay_us(uint16_t delay);
-void delay_ms(u16 delay);
+void delay_ms(uint16_t delay);
 
 #endif

src/jtag/drivers/OpenULINK/include/jtag.h

@@ -21,28 +21,28 @@
 #ifndef __JTAG_H
 #define __JTAG_H
 
-#include "shorttypes.h"
+#include <stdint.h>
 
 #define NOP {__asm nop __endasm;}
 
-void jtag_scan_in(u8 out_offset, u8 in_offset);
+void jtag_scan_in(uint8_t out_offset, uint8_t in_offset);
-void jtag_slow_scan_in(u8 out_offset, u8 in_offset);
+void jtag_slow_scan_in(uint8_t out_offset, uint8_t in_offset);
 
-void jtag_scan_out(u8 out_offset);
+void jtag_scan_out(uint8_t out_offset);
-void jtag_slow_scan_out(u8 out_offset);
+void jtag_slow_scan_out(uint8_t out_offset);
 
-void jtag_scan_io(u8 out_offset, u8 in_offset);
+void jtag_scan_io(uint8_t out_offset, uint8_t in_offset);
-void jtag_slow_scan_io(u8 out_offset, u8 in_offset);
+void jtag_slow_scan_io(uint8_t out_offset, uint8_t in_offset);
 
-void jtag_clock_tck(u16 count);
+void jtag_clock_tck(uint16_t count);
-void jtag_slow_clock_tck(u16 count);
+void jtag_slow_clock_tck(uint16_t count);
-void jtag_clock_tms(u8 count, u8 sequence);
+void jtag_clock_tms(uint8_t count, uint8_t sequence);
-void jtag_slow_clock_tms(u8 count, u8 sequence);
+void jtag_slow_clock_tms(uint8_t count, uint8_t sequence);
 
-u16  jtag_get_signals(void);
+uint16_t  jtag_get_signals(void);
-void jtag_set_signals(u8 low, u8 high);
+void jtag_set_signals(uint8_t low, uint8_t high);
 
-void jtag_configure_tck_delay(u8 scan_in, u8 scan_out, u8 scan_io, u8 tck,
+void jtag_configure_tck_delay(uint8_t scan_in, uint8_t scan_out,
-    u8 tms);
+    uint8_t scan_io, uint8_t tck, uint8_t tms);
 
 #endif

src/jtag/drivers/OpenULINK/include/protocol.h

@@ -21,7 +21,6 @@
 #ifndef __PROTOCOL_H
 #define __PROTOCOL_H
 
-#include "shorttypes.h"
 #include "common.h"
 #include <stdbool.h>
 

src/jtag/drivers/OpenULINK/include/shorttypes.h

@@ -1,41 +0,0 @@
-/***************************************************************************
- *   Copyright (C) 2011 by Martin Schmoelzer                               *
- *   <martin.schmoelzer@student.tuwien.ac.at>                              *
- *                                                                         *
- *   This program is free software; you can redistribute it and/or modify  *
- *   it under the terms of the GNU General Public License as published by  *
- *   the Free Software Foundation; either version 2 of the License, or     *
- *   (at your option) any later version.                                   *
- *                                                                         *
- *   This program is distributed in the hope that it will be useful,       *
- *   but WITHOUT ANY WARRANTY; without even the implied warranty of        *
- *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the         *
- *   GNU General Public License for more details.                          *
- *                                                                         *
- *   You should have received a copy of the GNU General Public License     *
- *   along with this program; if not, write to the                         *
- *   Free Software Foundation, Inc.,                                       *
- *   59 Temple Place - Suite 330, Boston, MA  02111-1307, USA.             *
- ***************************************************************************/
-
-#ifndef __SHORTTYPES_H
-#define __SHORTTYPES_H
-
-#include <stdint.h>
-
-/**
- * @file Integer type definitions for shorter code (easier to stay within 80
- * character maximum line length).
- */
-
-/* Signed integers */
-typedef int8_t   s8;
-typedef int16_t  s16;
-typedef int32_t  s32;
-
-/* Unsigned integers */
-typedef uint8_t  u8;
-typedef uint16_t u16;
-typedef uint32_t u32;
-
-#endif

src/jtag/drivers/OpenULINK/include/usb.h

@@ -21,16 +21,16 @@
 #ifndef __USB_H
 #define __USB_H
 
-#include "shorttypes.h"
 #include "reg_ezusb.h"
 
+#include <stdint.h>
 #include <stdbool.h>
 
 #define NULL        (void*)0;
 
-/* High and Low byte of a word (u16) */
+/* High and Low byte of a word (uint16_t) */
-#define HI8(word)   (u8)(((u16)word >> 8) & 0xff)
+#define HI8(word)   (uint8_t)(((uint16_t)word >> 8) & 0xff)
-#define LO8(word)   (u8)((u16)word & 0xff)
+#define LO8(word)   (uint8_t)((uint16_t)word & 0xff)
 
 /* Convenience functions */
 #define STALL_EP0()   EP0CS |= EP0STALL
@@ -49,80 +49,80 @@
 
 /** USB Device Descriptor. See USB 1.1 spec, pp. 196 - 198 */
 struct usb_device_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< DEVICE Descriptor Type.
+  uint8_t  bDescriptorType;    ///< DEVICE Descriptor Type.
-  u16 bcdUSB;              ///< USB specification release number (BCD).
+  uint16_t bcdUSB;             ///< USB specification release number (BCD).
-  u8  bDeviceClass;        ///< Class code.
+  uint8_t  bDeviceClass;       ///< Class code.
-  u8  bDeviceSubClass;     ///< Subclass code.
+  uint8_t  bDeviceSubClass;    ///< Subclass code.
-  u8  bDeviceProtocol;     ///< Protocol code.
+  uint8_t  bDeviceProtocol;    ///< Protocol code.
-  u8  bMaxPacketSize0;     ///< Maximum packet size for EP0 (8, 16, 32, 64).
+  uint8_t  bMaxPacketSize0;    ///< Maximum packet size for EP0 (8, 16, 32, 64).
-  u16 idVendor;            ///< USB Vendor ID.
+  uint16_t idVendor;           ///< USB Vendor ID.
-  u16 idProduct;           ///< USB Product ID.
+  uint16_t idProduct;          ///< USB Product ID.
-  u16 bcdDevice;           ///< Device Release Number (BCD).
+  uint16_t bcdDevice;          ///< Device Release Number (BCD).
-  u8  iManufacturer;       ///< Index of manufacturer string descriptor.
+  uint8_t  iManufacturer;      ///< Index of manufacturer string descriptor.
-  u8  iProduct;            ///< Index of product string descriptor.
+  uint8_t  iProduct;           ///< Index of product string descriptor.
-  u8  iSerialNumber;       ///< Index of string descriptor containing serial #.
+  uint8_t  iSerialNumber;      ///< Index of string descriptor containing serial #.
-  u8  bNumConfigurations;  ///< Number of possible configurations.
+  uint8_t  bNumConfigurations; ///< Number of possible configurations.
 };
 
 /** USB Configuration Descriptor. See USB 1.1 spec, pp. 199 - 200 */
 struct usb_config_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< CONFIGURATION descriptor type.
+  uint8_t  bDescriptorType;    ///< CONFIGURATION descriptor type.
-  u16 wTotalLength;        ///< Combined total length of all descriptors.
+  uint16_t wTotalLength;       ///< Combined total length of all descriptors.
-  u8  bNumInterfaces;      ///< Number of interfaces in this configuration.
+  uint8_t  bNumInterfaces;     ///< Number of interfaces in this configuration.
-  u8  bConfigurationValue; ///< Value used to select this configuration.
+  uint8_t  bConfigurationValue;///< Value used to select this configuration.
-  u8  iConfiguration;      ///< Index of configuration string descriptor.
+  uint8_t  iConfiguration;     ///< Index of configuration string descriptor.
-  u8  bmAttributes;        ///< Configuration characteristics.
+  uint8_t  bmAttributes;       ///< Configuration characteristics.
-  u8  MaxPower;            ///< Maximum power consumption in 2 mA units.
+  uint8_t  MaxPower;           ///< Maximum power consumption in 2 mA units.
 };
 
 /** USB Interface Descriptor. See USB 1.1 spec, pp. 201 - 203 */
 struct usb_interface_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< INTERFACE descriptor type.
+  uint8_t  bDescriptorType;    ///< INTERFACE descriptor type.
-  u8  bInterfaceNumber;    ///< Interface number.
+  uint8_t  bInterfaceNumber;   ///< Interface number.
-  u8  bAlternateSetting;   ///< Value used to select alternate setting.
+  uint8_t  bAlternateSetting;  ///< Value used to select alternate setting.
-  u8  bNumEndpoints;       ///< Number of endpoints used by this interface.
+  uint8_t  bNumEndpoints;      ///< Number of endpoints used by this interface.
-  u8  bInterfaceClass;     ///< Class code.
+  uint8_t  bInterfaceClass;    ///< Class code.
-  u8  bInterfaceSubclass;  ///< Subclass code.
+  uint8_t  bInterfaceSubclass; ///< Subclass code.
-  u8  bInterfaceProtocol;  ///< Protocol code.
+  uint8_t  bInterfaceProtocol; ///< Protocol code.
-  u8  iInterface;          ///< Index of interface string descriptor.
+  uint8_t  iInterface;         ///< Index of interface string descriptor.
 };
 
 /** USB Endpoint Descriptor. See USB 1.1 spec, pp. 203 - 204 */
 struct usb_endpoint_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< ENDPOINT descriptor type.
+  uint8_t  bDescriptorType;    ///< ENDPOINT descriptor type.
-  u8  bEndpointAddress;    ///< Endpoint Address: USB 1.1 spec, table 9-10.
+  uint8_t  bEndpointAddress;   ///< Endpoint Address: USB 1.1 spec, table 9-10.
-  u8  bmAttributes;        ///< Endpoint Attributes: USB 1.1 spec, table 9-10.
+  uint8_t  bmAttributes;       ///< Endpoint Attributes: USB 1.1 spec, table 9-10.
-  u16 wMaxPacketSize;      ///< Maximum packet size for this endpoint.
+  uint16_t wMaxPacketSize;     ///< Maximum packet size for this endpoint.
-  u8  bInterval;           ///< Polling interval (in ms) for this endpoint.
+  uint8_t  bInterval;          ///< Polling interval (in ms) for this endpoint.
 };
 
 /** USB Language Descriptor. See USB 1.1 spec, pp. 204 - 205 */
 struct usb_language_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< STRING descriptor type.
+  uint8_t  bDescriptorType;    ///< STRING descriptor type.
-  u16 wLANGID[];           ///< LANGID codes.
+  uint16_t wLANGID[];          ///< LANGID codes.
 };
 
 /** USB String Descriptor. See USB 1.1 spec, pp. 204 - 205 */
 struct usb_string_descriptor {
-  u8  bLength;             ///< Size of this descriptor in bytes.
+  uint8_t  bLength;            ///< Size of this descriptor in bytes.
-  u8  bDescriptorType;     ///< STRING descriptor type.
+  uint8_t  bDescriptorType;    ///< STRING descriptor type.
-  u16 bString[];           ///< UNICODE encoded string.
+  uint16_t bString[];          ///< UNICODE encoded string.
 };
 
 /********************** USB Control Endpoint 0 related *********************/
 
 /** USB Control Setup Data. See USB 1.1 spec, pp. 183 - 185 */
 struct setup_data {
-  u8  bmRequestType;       ///< Characteristics of a request.
+  uint8_t  bmRequestType;      ///< Characteristics of a request.
-  u8  bRequest;            ///< Specific request.
+  uint8_t  bRequest;           ///< Specific request.
-  u16 wValue;              ///< Field that varies according to request.
+  uint16_t wValue;             ///< Field that varies according to request.
-  u16 wIndex;              ///< Field that varies according to request.
+  uint16_t wIndex;             ///< Field that varies according to request.
-  u16 wLength;             ///< Number of bytes to transfer in data stage.
+  uint16_t wLength;            ///< Number of bytes to transfer in data stage.
 };
 
 /* External declarations for variables that need to be accessed outside of
@@ -252,8 +252,8 @@ enum usb_isr {
 
 /*************************** Function Prototypes ***************************/
 
-__xdata u8* usb_get_endpoint_cs_reg(u8 ep);
+__xdata uint8_t* usb_get_endpoint_cs_reg(uint8_t ep);
-void usb_reset_data_toggle(u8 ep);
+void usb_reset_data_toggle(uint8_t ep);
 
 bool usb_handle_get_status(void);
 bool usb_handle_clear_feature(void);

src/jtag/drivers/OpenULINK/src/delay.c

@@ -26,24 +26,24 @@ void delay_5us(void)
 }
 
 void delay_1ms(void) {
-  u16 i;
+  uint16_t i;
 
   for (i = 0; i < 598; i++);
 }
 
-void delay_us(u16 delay)
+void delay_us(uint16_t delay)
 {
-  u16 i;
+  uint16_t i;
-  u16 maxcount = (delay / 5);
+  uint16_t maxcount = (delay / 5);
 
   for (i = 0; i < maxcount; i++) {
     delay_5us();
   }
 }
 
-void delay_ms(u16 delay)
+void delay_ms(uint16_t delay)
 {
-  u16 i;
+  uint16_t i;
 
   for (i = 0; i < delay; i++) {
     delay_1ms();

src/jtag/drivers/OpenULINK/src/jtag.c

@@ -27,19 +27,19 @@
 #include <stdbool.h>
 
 /** Delay value for SCAN_IN operations with less than maximum TCK frequency */
-u8 delay_scan_in = 0;
+uint8_t delay_scan_in = 0;
 
 /** Delay value for SCAN_OUT operations with less than maximum TCK frequency */
-u8 delay_scan_out = 0;
+uint8_t delay_scan_out = 0;
 
 /** Delay value for SCAN_IO operations with less than maximum TCK frequency */
-u8 delay_scan_io = 0;
+uint8_t delay_scan_io = 0;
 
 /** Delay value for CLOCK_TCK operations with less than maximum frequency */
-u8 delay_tck = 0;
+uint8_t delay_tck = 0;
 
 /** Delay value for CLOCK_TMS operations with less than maximum frequency */
-u8 delay_tms = 0;
+uint8_t delay_tms = 0;
 
 /**
  * Perform JTAG SCAN-IN operation at maximum TCK frequency.
@@ -51,14 +51,14 @@ u8 delay_tms = 0;
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_scan_in(u8 out_offset, u8 in_offset)
+void jtag_scan_in(uint8_t out_offset, uint8_t in_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdo_data, i, j;
+  uint8_t tdo_data, i, j;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -132,14 +132,14 @@ void jtag_scan_in(u8 out_offset, u8 in_offset)
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_slow_scan_in(u8 out_offset, u8 in_offset)
+void jtag_slow_scan_in(uint8_t out_offset, uint8_t in_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdo_data, i, j, k;
+  uint8_t tdo_data, i, j, k;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -220,14 +220,14 @@ void jtag_slow_scan_in(u8 out_offset, u8 in_offset)
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_scan_out(u8 out_offset)
+void jtag_scan_out(uint8_t out_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdi_data, i, j;
+  uint8_t tdi_data, i, j;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -301,14 +301,14 @@ void jtag_scan_out(u8 out_offset)
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_slow_scan_out(u8 out_offset)
+void jtag_slow_scan_out(uint8_t out_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdi_data, i, j, k;
+  uint8_t tdi_data, i, j, k;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -388,14 +388,14 @@ void jtag_slow_scan_out(u8 out_offset)
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_scan_io(u8 out_offset, u8 in_offset)
+void jtag_scan_io(uint8_t out_offset, uint8_t in_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdi_data, tdo_data, i, j;
+  uint8_t tdi_data, tdo_data, i, j;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -488,14 +488,14 @@ void jtag_scan_io(u8 out_offset, u8 in_offset)
  *
  * @param out_offset offset in OUT2BUF where payload data starts
  */
-void jtag_slow_scan_io(u8 out_offset, u8 in_offset)
+void jtag_slow_scan_io(uint8_t out_offset, uint8_t in_offset)
 {
-  u8 scan_size_bytes, bits_last_byte;
+  uint8_t scan_size_bytes, bits_last_byte;
-  u8 tms_count_start, tms_count_end;
+  uint8_t tms_count_start, tms_count_end;
-  u8 tms_sequence_start, tms_sequence_end;
+  uint8_t tms_sequence_start, tms_sequence_end;
-  u8 tdi_data, tdo_data, i, j, k;
+  uint8_t tdi_data, tdo_data, i, j, k;
 
-  u8 outb_buffer;
+  uint8_t outb_buffer;
 
   /* Get parameters from OUT2BUF */
   scan_size_bytes = OUT2BUF[out_offset];
@@ -590,10 +590,10 @@ void jtag_slow_scan_io(u8 out_offset, u8 in_offset)
  *
  * @param count number of TCK clock cyclces to generate.
  */
-void jtag_clock_tck(u16 count)
+void jtag_clock_tck(uint16_t count)
 {
-  u16 i;
+  uint16_t i;
-  u8 outb_buffer = OUTB & ~(PIN_TCK);
+  uint8_t outb_buffer = OUTB & ~(PIN_TCK);
 
   for ( i = 0; i < count; i++ ) {
     OUTB = outb_buffer;
@@ -608,11 +608,11 @@ void jtag_clock_tck(u16 count)
  *
  * @param count number of TCK clock cyclces to generate.
  */
-void jtag_slow_clock_tck(u16 count)
+void jtag_slow_clock_tck(uint16_t count)
 {
-  u16 i;
+  uint16_t i;
-  u8 j;
+  uint8_t j;
-  u8 outb_buffer = OUTB & ~(PIN_TCK);
+  uint8_t outb_buffer = OUTB & ~(PIN_TCK);
 
   for ( i = 0; i < count; i++ ) {
     OUTB = outb_buffer;
@@ -631,10 +631,10 @@ void jtag_slow_clock_tck(u16 count)
  * @param sequence the TMS pin levels for each state transition, starting with
  *  the least-significant bit.
  */
-void jtag_clock_tms(u8 count, u8 sequence)
+void jtag_clock_tms(uint8_t count, uint8_t sequence)
 {
-  u8 outb_buffer = OUTB & ~(PIN_TCK);
+  uint8_t outb_buffer = OUTB & ~(PIN_TCK);
-  u8 i;
+  uint8_t i;
 
   for ( i = 0; i < count; i++ ) {
     /* Set TMS pin according to sequence parameter */
@@ -660,10 +660,10 @@ void jtag_clock_tms(u8 count, u8 sequence)
  * @param sequence the TMS pin levels for each state transition, starting with
  *  the least-significant bit.
  */
-void jtag_slow_clock_tms(u8 count, u8 sequence)
+void jtag_slow_clock_tms(uint8_t count, uint8_t sequence)
 {
-  u8 outb_buffer = OUTB & ~(PIN_TCK);
+  uint8_t outb_buffer = OUTB & ~(PIN_TCK);
-  u8 i, j;
+  uint8_t i, j;
 
   for (i = 0; i < count; i++) {
     /* Set TMS pin according to sequence parameter */
@@ -689,9 +689,9 @@ void jtag_slow_clock_tms(u8 count, u8 sequence)
  *  of the JTAG input signals and the least-significant byte cotains the state
  *  of the JTAG output signals.
  */
-u16 jtag_get_signals(void)
+uint16_t jtag_get_signals(void)
 {
-  u8 input_signal_state, output_signal_state;
+  uint8_t input_signal_state, output_signal_state;
 
   input_signal_state = 0;
   output_signal_state = 0;
@@ -715,7 +715,7 @@ u16 jtag_get_signals(void)
   /* Get states of output pins */
   output_signal_state = PINSB & MASK_PORTB_DIRECTION_OUT;
 
-  return ((u16)input_signal_state << 8) | ((u16)output_signal_state);
+  return ((uint16_t)input_signal_state << 8) | ((uint16_t)output_signal_state);
 }
 
 /**
@@ -724,7 +724,7 @@ u16 jtag_get_signals(void)
  * @param low signals which should be de-asserted.
  * @param high signals which should be asserted.
  */
-void jtag_set_signals(u8 low, u8 high)
+void jtag_set_signals(uint8_t low, uint8_t high)
 {
   OUTB &= ~(low & MASK_PORTB_DIRECTION_OUT);
   OUTB |= (high & MASK_PORTB_DIRECTION_OUT);
@@ -739,8 +739,8 @@ void jtag_set_signals(u8 low, u8 high)
  * @param tck number of delay cycles in clock_tck operations.
  * @param tms number of delay cycles in clock_tms operations.
  */
-void jtag_configure_tck_delay(u8 scan_in, u8 scan_out, u8 scan_io, u8 tck,
+void jtag_configure_tck_delay(uint8_t scan_in, uint8_t scan_out,
-    u8 tms)
+    uint8_t scan_io, uint8_t tck, uint8_t tms)
 {
   delay_scan_in = scan_in;
   delay_scan_out = scan_out;

src/jtag/drivers/OpenULINK/src/main.c

@@ -20,7 +20,6 @@
 
 #include "main.h"
 
-#include "shorttypes.h"
 #include "io.h"
 #include "usb.h"
 #include "protocol.h"

src/jtag/drivers/OpenULINK/src/protocol.c

@@ -47,17 +47,17 @@
  */
 
 /** Index in EP2 Bulk-OUT data buffer that contains the current command ID */
-volatile u8 cmd_id_index;
+volatile uint8_t cmd_id_index;
 
 /** Number of data bytes already in EP2 Bulk-IN buffer */
-volatile u8 payload_index_in;
+volatile uint8_t payload_index_in;
 
 /**
  * Execute a SET_LEDS command.
  */
 void execute_set_led_command(void)
 {
-  u8 led_state = OUT2BUF[cmd_id_index + 1];
+  uint8_t led_state = OUT2BUF[cmd_id_index + 1];
 
   if (led_state & RUN_LED_ON) {
     SET_RUN_LED();
@@ -87,9 +87,9 @@ void execute_set_led_command(void)
  */
 bool execute_command(void)
 {
-  u8 usb_out_bytecount, usb_in_bytecount;
+  uint8_t usb_out_bytecount, usb_in_bytecount;
-  u16 signal_state;
+  uint16_t signal_state;
-  u16 count;
+  uint16_t count;
 
   /* Most commands do not transfer IN data. To save code space, we write 0 to
    * usb_in_bytecount here, then modify it in the switch statement below where
@@ -117,8 +117,8 @@ bool execute_command(void)
     break;
   case CMD_CLOCK_TCK:
     usb_out_bytecount = 2;
-    count = (u16)OUT2BUF[cmd_id_index + 1];
+    count = (uint16_t)OUT2BUF[cmd_id_index + 1];
-    count |= ((u16)OUT2BUF[cmd_id_index + 2]) << 8;
+    count |= ((uint16_t)OUT2BUF[cmd_id_index + 2]) << 8;
     jtag_clock_tck(count);
     break;
   case CMD_SLOW_SCAN_IN:
@@ -141,20 +141,20 @@ bool execute_command(void)
     break;
   case CMD_SLOW_CLOCK_TCK:
     usb_out_bytecount = 2;
-    count = (u16)OUT2BUF[cmd_id_index + 1];
+    count = (uint16_t)OUT2BUF[cmd_id_index + 1];
-    count |= ((u16)OUT2BUF[cmd_id_index + 2]) << 8;
+    count |= ((uint16_t)OUT2BUF[cmd_id_index + 2]) << 8;
     jtag_slow_clock_tck(count);
     break;
   case CMD_SLEEP_US:
     usb_out_bytecount = 2;
-    count = (u16)OUT2BUF[cmd_id_index + 1];
+    count = (uint16_t)OUT2BUF[cmd_id_index + 1];
-    count |= ((u16)OUT2BUF[cmd_id_index + 2]) << 8;
+    count |= ((uint16_t)OUT2BUF[cmd_id_index + 2]) << 8;
     delay_us(count);
     break;
   case CMD_SLEEP_MS:
     usb_out_bytecount = 2;
-    count = (u16)OUT2BUF[cmd_id_index + 1];
+    count = (uint16_t)OUT2BUF[cmd_id_index + 1];
-    count |= ((u16)OUT2BUF[cmd_id_index + 2]) << 8;
+    count |= ((uint16_t)OUT2BUF[cmd_id_index + 2]) << 8;
     delay_ms(count);
     break;
   case CMD_GET_SIGNALS:

src/jtag/drivers/OpenULINK/src/usb.c

@@ -205,10 +205,10 @@ void ep7out_isr(void)   __interrupt EP7OUT_ISR   { }
  *  specified in \a ep
  * @return on failure: NULL
  */
-__xdata u8* usb_get_endpoint_cs_reg(u8 ep)
+__xdata uint8_t* usb_get_endpoint_cs_reg(uint8_t ep)
 {
   /* Mask direction bit */
-  u8 ep_num = ep & 0x7F;
+  uint8_t ep_num = ep & 0x7F;
 
   switch (ep_num) {
   case 0:
@@ -240,7 +240,7 @@ __xdata u8* usb_get_endpoint_cs_reg(u8 ep)
   return NULL;
 }
 
-void usb_reset_data_toggle(u8 ep)
+void usb_reset_data_toggle(uint8_t ep)
 {
   /* TOGCTL register:
      +----+-----+-----+------+-----+-------+-------+-------+
@@ -251,7 +251,7 @@ void usb_reset_data_toggle(u8 ep)
      to the IO bit and the endpoint number to the EP2..EP0 bits. Then, in a
      separate write cycle, the R bit needs to be set.
   */
-  u8 togctl_value = (ep & 0x80 >> 3) | (ep & 0x7);
+  uint8_t togctl_value = (ep & 0x80 >> 3) | (ep & 0x7);
 
   /* First step: Write EP number and direction bit */
   TOGCTL = togctl_value;
@@ -269,7 +269,7 @@ void usb_reset_data_toggle(u8 ep)
  */
 bool usb_handle_get_status(void)
 {
-  u8 *ep_cs;
+  uint8_t *ep_cs;
 
   switch (setup_data.bmRequestType) {
   case GS_DEVICE:
@@ -322,7 +322,7 @@ bool usb_handle_get_status(void)
  */
 bool usb_handle_clear_feature(void)
 {
-  __xdata u8 *ep_cs;
+  __xdata uint8_t *ep_cs;
 
   switch (setup_data.bmRequestType) {
   case CF_DEVICE:
@@ -358,7 +358,7 @@ bool usb_handle_clear_feature(void)
  */
 bool usb_handle_set_feature(void)
 {
-  __xdata u8 *ep_cs;
+  __xdata uint8_t *ep_cs;
 
   switch (setup_data.bmRequestType) {
   case SF_DEVICE:
@@ -396,8 +396,8 @@ bool usb_handle_set_feature(void)
  */
 bool usb_handle_get_descriptor(void)
 {
-  __xdata u8 descriptor_type;
+  __xdata uint8_t descriptor_type;
-  __xdata u8 descriptor_index;
+  __xdata uint8_t descriptor_index;
 
   descriptor_type = (setup_data.wValue & 0xff00) >> 8;
   descriptor_index = setup_data.wValue & 0x00ff;