David Brownell <david-b@pacbell.net>:
Continue updating the NOR flash coverage to use @deffn syntax, so the commands have more consistent presentation and formatting. This reorganizes information and updates its presentation, except where the information didn't really match the code. This patch updates the main commands, and finishes making the section structure parallel the NAND presentation. Of note: - The "flash fill[whb] addr value length" commands are now documented. - The "flash bank" command is now presented much earlier - Explicit mention is made that NOR flash should be read using just standard memory access commands, like "mdw" and "dump_image". git-svn-id: svn://svn.berlios.de/openocd/trunk@1938 b42882b7-edfa-0310-969c-e2dbd0fdcd60
This commit is contained in:
zwelch
parent
f37a8136fe
commit
6149c509ca
246
doc/openocd.texi
246
doc/openocd.texi
|
|
@ -64,7 +64,7 @@ This manual documents edition @value{EDITION} of the Open On-Chip Debugger
|
|||
* Reset Configuration:: Reset Configuration
|
||||
* Tap Creation:: Tap Creation
|
||||
* Target Configuration:: Target Configuration
|
||||
* Flash Configuration:: Flash Configuration
|
||||
* Flash Commands:: Flash Commands
|
||||
* NAND Flash Commands:: NAND Flash Commands
|
||||
* General Commands:: General Commands
|
||||
* JTAG Commands:: JTAG Commands
|
||||
|
|
@ -2305,9 +2305,8 @@ still use this that need to be converted.
|
|||
@end example
|
||||
@* The target# is a the 0 based target numerical index.
|
||||
|
||||
@node Flash Configuration
|
||||
@chapter Flash programming
|
||||
@cindex Flash Configuration
|
||||
@node Flash Commands
|
||||
@chapter Flash Commands
|
||||
|
||||
OpenOCD has different commands for NOR and NAND flash;
|
||||
the ``flash'' command works with NOR flash, while
|
||||
|
|
@ -2319,94 +2318,35 @@ used. (SPI flash must also be copied to memory before use.)
|
|||
However, the documentation also uses ``flash'' as a generic term;
|
||||
for example, ``Put flash configuration in board-specific files''.
|
||||
|
||||
@b{Note:} As of 28/nov/2008 OpenOCD does not know how to program a SPI
|
||||
@quotation Note
|
||||
As of 28-nov-2008 OpenOCD does not know how to program a SPI
|
||||
flash that a micro may boot from. Perhaps you, the reader, would like to
|
||||
contribute support for this.
|
||||
@end quotation
|
||||
|
||||
Flash Steps:
|
||||
@enumerate
|
||||
@item Configure via the command @b{flash bank}
|
||||
@* Normally this is done in a configuration file.
|
||||
@item Operate on the flash via @b{flash SOMECOMMAND}
|
||||
@item Configure via the command @command{flash bank}
|
||||
@* Do this in a board-specific configuration file,
|
||||
passing parameters as needed by the driver.
|
||||
@item Operate on the flash via @command{flash subcommand}
|
||||
@* Often commands to manipulate the flash are typed by a human, or run
|
||||
via a script in some automated way. For example: To program the boot
|
||||
flash on your board.
|
||||
via a script in some automated way. Common tasks include writing a
|
||||
boot loader, operating system, or other data.
|
||||
@item GDB Flashing
|
||||
@* Flashing via GDB requires the flash be configured via ``flash
|
||||
bank'', and the GDB flash features be enabled.
|
||||
@xref{GDB Configuration}.
|
||||
@end enumerate
|
||||
|
||||
@section Flash commands
|
||||
@cindex Flash commands
|
||||
@subsection flash banks
|
||||
@b{flash banks}
|
||||
@cindex flash banks
|
||||
@*List configured flash banks
|
||||
@*@b{NOTE:} the singular form: 'flash bank' is used to configure the flash banks.
|
||||
@subsection flash info
|
||||
@b{flash info} <@var{num}>
|
||||
@cindex flash info
|
||||
@*Print info about flash bank <@option{num}>
|
||||
@subsection flash probe
|
||||
@b{flash probe} <@var{num}>
|
||||
@cindex flash probe
|
||||
@*Identify the flash, or validate the parameters of the configured flash. Operation
|
||||
depends on the flash type.
|
||||
@subsection flash erase_check
|
||||
@b{flash erase_check} <@var{num}>
|
||||
@cindex flash erase_check
|
||||
@*Check erase state of sectors in flash bank <@var{num}>. This is the only operation that
|
||||
updates the erase state information displayed by @option{flash info}. That means you have
|
||||
to issue an @option{erase_check} command after erasing or programming the device to get
|
||||
updated information.
|
||||
@subsection flash protect_check
|
||||
@b{flash protect_check} <@var{num}>
|
||||
@cindex flash protect_check
|
||||
@*Check protection state of sectors in flash bank <num>.
|
||||
@option{flash erase_sector} using the same syntax.
|
||||
@subsection flash erase_sector
|
||||
@b{flash erase_sector} <@var{num}> <@var{first}> <@var{last}>
|
||||
@cindex flash erase_sector
|
||||
@anchor{flash erase_sector}
|
||||
@*Erase sectors at bank <@var{num}>, starting at sector <@var{first}> up to and including
|
||||
<@var{last}>. Sector numbering starts at 0. Depending on the flash type, erasing may
|
||||
require the protection to be disabled first (e.g. Intel Advanced Bootblock flash using
|
||||
the CFI driver).
|
||||
@subsection flash erase_address
|
||||
@b{flash erase_address} <@var{address}> <@var{length}>
|
||||
@cindex flash erase_address
|
||||
@*Erase sectors starting at <@var{address}> for <@var{length}> bytes
|
||||
@subsection flash write_bank
|
||||
@b{flash write_bank} <@var{num}> <@var{file}> <@var{offset}>
|
||||
@cindex flash write_bank
|
||||
@anchor{flash write_bank}
|
||||
@*Write the binary <@var{file}> to flash bank <@var{num}>, starting at
|
||||
<@option{offset}> bytes from the beginning of the bank.
|
||||
@subsection flash write_image
|
||||
@b{flash write_image} [@var{erase}] <@var{file}> [@var{offset}] [@var{type}]
|
||||
@cindex flash write_image
|
||||
@anchor{flash write_image}
|
||||
@*Write the image <@var{file}> to the current target's flash bank(s). A relocation
|
||||
[@var{offset}] can be specified and the file [@var{type}] can be specified
|
||||
explicitly as @option{bin} (binary), @option{ihex} (Intel hex), @option{elf}
|
||||
(ELF file) or @option{s19} (Motorola s19). Flash memory will be erased prior to programming
|
||||
if the @option{erase} parameter is given.
|
||||
@subsection flash protect
|
||||
@b{flash protect} <@var{num}> <@var{first}> <@var{last}> <@option{on}|@option{off}>
|
||||
@cindex flash protect
|
||||
@*Enable (@var{on}) or disable (@var{off}) protection of flash sectors <@var{first}> to
|
||||
<@var{last}> of @option{flash bank} <@var{num}>.
|
||||
Many CPUs have the ablity to ``boot'' from the first flash bank.
|
||||
This means that misprograming that bank can ``brick'' a system,
|
||||
so that it can't boot.
|
||||
JTAG tools, like OpenOCD, are often then used to ``de-brick'' the
|
||||
board by (re)installing working boot firmware.
|
||||
|
||||
@section flash bank command
|
||||
The @command{flash bank} command is used to configure one or more flash
|
||||
chips (or @emph{banks} in OpenOCD terms).
|
||||
Most CPUs have the ablity to ``boot'' from the first flash bank.
|
||||
|
||||
@quotation Note
|
||||
This command is not available after OpenOCD initialization has completed.
|
||||
Use it in board specific configuration files, not interactively.
|
||||
@end quotation
|
||||
@section Flash Configuration Commands
|
||||
@cindex flash configuration
|
||||
|
||||
@deffn {Config Command} {flash bank} driver base size chip_width bus_width target [driver_options]
|
||||
Configures a flash bank which provides persistent storage
|
||||
|
|
@ -2435,6 +2375,152 @@ commands to the flash controller.
|
|||
additional parameters. See the driver-specific documentation
|
||||
for more information.
|
||||
@end itemize
|
||||
@quotation Note
|
||||
This command is not available after OpenOCD initialization has completed.
|
||||
Use it in board specific configuration files, not interactively.
|
||||
@end quotation
|
||||
@end deffn
|
||||
|
||||
@comment the REAL name for this command is "ocd_flash_banks"
|
||||
@comment less confusing would be: "flash list" (like "nand list")
|
||||
@deffn Command {flash banks}
|
||||
Prints a one-line summary of each device declared
|
||||
using @command{flash bank}, numbered from zero.
|
||||
Note that this is the @emph{plural} form;
|
||||
the @emph{singular} form is a very different command.
|
||||
@end deffn
|
||||
|
||||
@deffn Command {flash probe} num
|
||||
Identify the flash, or validate the parameters of the configured flash. Operation
|
||||
depends on the flash type.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
Most flash commands will implicitly @emph{autoprobe} the bank;
|
||||
flash drivers can distinguish between probing and autoprobing,
|
||||
but most don't bother.
|
||||
@end deffn
|
||||
|
||||
@section Erasing, Reading, Writing to Flash
|
||||
@cindex flash erasing
|
||||
@cindex flash reading
|
||||
@cindex flash writing
|
||||
@cindex flash programming
|
||||
|
||||
One feature distinguishing NOR flash from NAND or serial flash technologies
|
||||
is that for read access, it acts exactly like any other addressible memory.
|
||||
This means you can use normal memory read commands like @command{mdw} or
|
||||
@command{dump_image} with it, with no special @command{flash} subcommands.
|
||||
@xref{Memory access}.
|
||||
@xref{Image access}.
|
||||
|
||||
Write access works differently. Flash memory normally needs to be erased
|
||||
before it's written. Erasing a sector turns all of its bits to ones, and
|
||||
writing can turn ones into zeroes. This is why there are special commands
|
||||
for interactive erasing and writing, and why GDB needs to know which parts
|
||||
of the address space hold NOR flash memory.
|
||||
|
||||
@quotation Note
|
||||
Most of these erase and write commands leverage the fact that NOR flash
|
||||
chips consume target address space. They implicitly refer to the current
|
||||
JTAG target, and map from an address in that target's address space
|
||||
back to a flash bank.
|
||||
@comment In May 2009, those mappings may fail if any bank associated
|
||||
@comment with that target doesn't succesfuly autoprobe ... bug worth fixing?
|
||||
A few commands use abstract addressing based on bank and sector numbers,
|
||||
and don't depend on searching the current target and its address space.
|
||||
Avoid confusing the two command models.
|
||||
@end quotation
|
||||
|
||||
Some flash chips implement software protection against accidental writes,
|
||||
since such buggy writes could in some cases ``brick'' a system.
|
||||
For such systems, erasing and writing may require sector protection to be
|
||||
disabled first.
|
||||
Examples include CFI flash such as ``Intel Advanced Bootblock flash'',
|
||||
and AT91SAM7 on-chip flash.
|
||||
@xref{flash protect}.
|
||||
|
||||
@anchor{flash erase_sector}
|
||||
@deffn Command {flash erase_sector} num first last
|
||||
Erase sectors in bank @var{num}, starting at sector @var{first} up to and including
|
||||
@var{last}. Sector numbering starts at 0.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
@end deffn
|
||||
|
||||
@deffn Command {flash erase_address} address length
|
||||
Erase sectors starting at @var{address} for @var{length} bytes.
|
||||
The flash bank to use is inferred from the @var{address}, and
|
||||
the specified length must stay within that bank.
|
||||
As a special case, when @var{length} is zero and @var{address} is
|
||||
the start of the bank, the whole flash is erased.
|
||||
@end deffn
|
||||
|
||||
@deffn Command {flash fillw} address word length
|
||||
@deffnx Command {flash fillh} address halfword length
|
||||
@deffnx Command {flash fillb} address byte length
|
||||
Fills flash memory with the specified @var{word} (32 bits),
|
||||
@var{halfword} (16 bits), or @var{byte} (8-bit) pattern,
|
||||
starting at @var{address} and continuing
|
||||
for @var{length} units (word/halfword/byte).
|
||||
No erasure is done before writing; when needed, that must be done
|
||||
before issuing this command.
|
||||
Writes are done in blocks of up to 1024 bytes, and each write is
|
||||
verified by reading back the data and comparing it to what was written.
|
||||
The flash bank to use is inferred from the @var{address} of
|
||||
each block, and the specified length must stay within that bank.
|
||||
@end deffn
|
||||
@comment no current checks for errors if fill blocks touch multiple banks!
|
||||
|
||||
@anchor{flash write_bank}
|
||||
@deffn Command {flash write_bank} num filename offset
|
||||
Write the binary @file{filename} to flash bank @var{num},
|
||||
starting at @var{offset} bytes from the beginning of the bank.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
@end deffn
|
||||
|
||||
@anchor{flash write_image}
|
||||
@deffn Command {flash write_image} [erase] filename [offset] [type]
|
||||
Write the image @file{filename} to the current target's flash bank(s).
|
||||
A relocation @var{offset} may be specified, in which case it is added
|
||||
to the base address for each section in the image.
|
||||
The file [@var{type}] can be specified
|
||||
explicitly as @option{bin} (binary), @option{ihex} (Intel hex), @option{elf}
|
||||
(ELF file) or @option{s19} (Motorola s19).
|
||||
The relevant flash sectors will be erased prior to programming
|
||||
if the @option{erase} parameter is given.
|
||||
The flash bank to use is inferred from the @var{address} of
|
||||
each image segment.
|
||||
@end deffn
|
||||
|
||||
@section Other Flash commands
|
||||
@cindex flash protection
|
||||
|
||||
@deffn Command {flash erase_check} num
|
||||
Check erase state of sectors in flash bank @var{num},
|
||||
and display that status.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
This is the only operation that
|
||||
updates the erase state information displayed by @option{flash info}. That means you have
|
||||
to issue an @command{flash erase_check} command after erasing or programming the device
|
||||
to get updated information.
|
||||
(Code execution may have invalidated any state records kept by OpenOCD.)
|
||||
@end deffn
|
||||
|
||||
@deffn Command {flash info} num
|
||||
Print info about flash bank @var{num}
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
The information includes per-sector protect status.
|
||||
@end deffn
|
||||
|
||||
@anchor{flash protect}
|
||||
@deffn Command {flash protect} num first last (on|off)
|
||||
Enable (@var{on}) or disable (@var{off}) protection of flash sectors
|
||||
@var{first} to @var{last} of flash bank @var{num}.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
@end deffn
|
||||
|
||||
@deffn Command {flash protect_check} num
|
||||
Check protection state of sectors in flash bank @var{num}.
|
||||
The @var{num} parameter is a value shown by @command{flash banks}.
|
||||
@comment @option{flash erase_sector} using the same syntax.
|
||||
@end deffn
|
||||
|
||||
@section Flash Drivers, Options, and Commands
|
||||
|
|
@ -3279,6 +3365,7 @@ state.
|
|||
|
||||
|
||||
@section Memory access commands
|
||||
@anchor{Memory access}
|
||||
@subsection meminfo
|
||||
display available RAM memory.
|
||||
@subsection Memory peek/poke type commands
|
||||
|
|
@ -3314,6 +3401,7 @@ SDRAM controller to enable SDRAM.
|
|||
@end itemize
|
||||
|
||||
@section Image loading commands
|
||||
@anchor{Image access}
|
||||
@subsection load_image
|
||||
@b{load_image} <@var{file}> <@var{address}> [@option{bin}|@option{ihex}|@option{elf}]
|
||||
@cindex load_image
|
||||
|
|
|
|||
Loading…
Reference in New Issue