create tcl/board/dm365evm.cfg

This config is only lightly tested, and doesn't work well yet;
but it's a start.

 * Notably missing is PLL configuration, since each DaVinci
   does that just a bit differently; and thus DDR2 setup.

 * The SRST workaround needed for the goof in the CPLD's VHDL
   depends on at least the not-yet-merged patch letting ARM9
   (and ARM7) chips perform resets that don't use SRST.

So this isn't yet suitable for debugging U-Boot.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

tcl/board/dm365evm.cfg

@@ -0,0 +1,147 @@
+# DM365 EVM board -- Beta
+#   http://focus.ti.com/docs/toolsw/folders/print/tmdxevm365.html
+#   http://support.spectrumdigital.com/boards/evmdm365
+
+source [find target/ti_dm365.cfg]
+
+# NOTE:  in Rev C boards, the CPLD ignores SRST from the ARM-20 JTAG
+# connector, so it doesn't affect generation of the reset signal.
+# Accordingly, resets require something else.  ICEpick could do it;
+# but its docs aren't generally available.
+#
+# At this writing, newer boards aren't available ... so assume no SRST.
+# Also ICEpick docs aren't available ... so we must use watchdog reset,
+# and hope the CPU isn't wedged or in a WFI loop (either of which can
+# block access to CPU and thus watchdog registers).
+
+reset_config trst_only
+$_TARGETNAME configure -event reset-assert "davinci_wdog_reset"
+
+# SW5.1 routes CS0: NAND vs OneNAND.
+# SW4.6:4 controls AEMIF width (8 for NAND, 16 for OneNand)
+# for boot-from-flash, those must agree with SW4.3:1 settings.
+
+if { [info exists CS0MODE] } {
+	# NAND or OneNAND
+	set CS0 $CS0MODE
+} else {
+	set CS0 ""
+	echo "WARNING:  CS0 configuration not known"
+	proc cs0_setup {a_emif} {}
+	proc flashprobe {} {}
+}
+
+set a_emif [dict get $dm365 a_emif]
+
+# As shipped:  boot from NAND.
+if { $CS0 == "NAND" } {
+	echo "CS0 NAND"
+
+	# NAND socket has two chipselects.  Default MT29F16G08FAA chip
+	# has 1GByte on each one.
+	# NOTE:  "hwecc4" here presumes that you're not updating anything
+	# that needs infix layout (e.g. UBL, old U-Boot, etc)
+	nand device low davinci $_TARGETNAME 0x02000000 hwecc4 $a_emif
+	nand device high davinci $_TARGETNAME 0x02004000 hwecc4 $a_emif
+
+	proc cs0_setup {a_emif} {
+		global dm365
+
+		# 8 bit EMIF
+		davinci_pinmux $dm365 2 0x00000016
+
+		# slow/pessimistic timings
+		set nand_timings 0x40400204
+		# fast (25% faster page reads)
+		#set nand_timings 0x0400008c
+
+		# CS0 == socketed NAND (default MT29F16G08FAA, 2 GBytes)
+		mww [expr $a_emif + 0x10] $nand_timings
+
+		# NANDFCR -- CS0 has NAND
+		mww [expr $a_emif + 0x60] 0x01
+	}
+	proc flashprobe {} {
+		nand probe 0
+		nand probe 1
+	}
+
+} elseif { $CS0 == "OneNAND" } {
+	echo "CS0 OneNAND"
+
+	# No support for this OneNAND in OpenOCD (yet) or Linux ...
+	# REVISIT OneNAND timings not verified to work!
+	echo "WARNING -- OneNAND not yet tested!"
+
+	proc cs0_setup {a_emif} {
+		global dm365
+
+		# 16 bit EMIF
+		davinci_pinmux $dm365 2 0x00000055
+
+		# CS0 == OneNAND (KFG1G16U2B-DIB6, 128 KBytes)
+		mww [expr $a_emif + 0x10] 0x00000001
+
+		# ONENANDCTRL -- CS0 has OneNAND, enable sync reads
+		mww [expr $a_emif + 0x5c] 0x0441
+	}
+	proc flashprobe {} { }
+}
+
+# NOTE:  disable or replace this call to dm365evm_init if you're
+# debugging new UBL/NANDboot code from SRAM.
+$_TARGETNAME configure -event reset-init { dm365evm_init }
+
+#
+# This post-reset init is called when the MMU isn't active, all IRQs
+# are disabled, etc.  It should do most of what a UBL does, except for
+# loading code (like U-Boot) into DRAM and running it.
+#
+proc dm365evm_init {} {
+	global dm365
+
+	echo "Initialize DM365 EVM board"
+
+	# CLKIN	= 24 MHz ... can't talk quickly to ARM yet
+	jtag_khz 1500
+
+	# FIXME -- PLL init
+
+	########################
+	# PINMUX setup
+
+	davinci_pinmux $dm365 0 0x00fd0000
+	davinci_pinmux $dm365 1 0x00145555
+	# mux2 controls AEMIF ... 8 bit for NAND, 16 for OneNand
+	davinci_pinmux $dm365 3 0x375affff
+	davinci_pinmux $dm365 4 0x55556555
+
+	########################
+	# PSC setup (minimal)
+
+	# DDR EMIF/13, AEMIF/14, UART0/19
+	psc_enable 13
+	psc_enable 14
+	psc_enable 19
+	psc_go
+
+	# FIXME setup DDR2 (needs PLL)
+
+	########################
+	# ASYNC EMIF
+
+	set a_emif [dict get $dm365 a_emif]
+
+	# AWCCR
+	mww [expr $a_emif + 0x04] 0xff
+	# CS0 == NAND or OneNAND
+	cs0_setup $a_emif
+	# CS1 == CPLD
+	mww [expr $a_emif + 0x14] 0x00a00505
+
+	# FIXME setup UART0
+
+	flashprobe
+}
+
+