mcb1700: Keil MCB1700 w/1768 config script

Ca. 93kBytes/s flashing speed @ 10MHz JTAG clock

Signed-off-by: Øyvind Harboe <oyvind.harboe@zylin.com>

tcl/board/mcb1700.cfg

@@ -0,0 +1,75 @@
+# Keil MCB1700 PCB with 1768
+# 
+# Reset init script sets it to 100MHz
+set CCLK 100000
+
+source [find target/lpc1768.cfg] 
+
+global MCB1700_CCLK
+set MCB1700_CCLK $CCLK
+
+$_TARGETNAME configure -event reset-start {
+	# Start *real slow* as we do not know the
+    # state the boot rom left the clock in
+	jtag_khz 10
+}
+
+# Set up 100MHz clock to CPU
+$_TARGETNAME configure -event reset-init {
+    # PLL0CON: Disable PLL
+	mww 0x400FC080 0x00000000
+    # PLLFEED
+	mww 0x400FC08C 0x000000AA
+    # PLLFEED
+	mww 0x400FC08C 0x00000055
+
+    # CCLK=PLL/4 (=100 MHz)
+	mww 0x400FC104 0x00000003
+    # CLKSRCSEL: Clock source = internal RC oscillator
+	mww 0x400FC10C 0x00000000
+
+    # PLL0CFG: M=50,N=1 -> PLL=400 MHz
+	mww 0x400FC084 0x00000031
+    # PLLFEED
+	mww 0x400FC08C 0x000000AA
+    # PLLFEED
+	mww 0x400FC08C 0x00000055
+
+	# PLL0CON: Enable PLL
+	mww 0x400FC080 0x00000001
+    # PLLFEED
+	mww 0x400FC08C 0x000000AA
+    # PLLFEED
+	mww 0x400FC08C 0x00000055
+
+	sleep 50
+
+    # PLL0CON: Connect PLL
+	mww 0x400FC080 0x00000003
+    # PLLFEED
+	mww 0x400FC08C 0x000000AA
+    # PLLFEED
+	mww 0x400FC08C 0x00000055
+
+	# Dividing CPU clock by 8 should be pretty conservative
+	#
+	# 
+	global MCB1700_CCLK
+	jtag_khz [expr $MCB1700_CCLK / 8]
+
+	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
+	# "User Flash Mode" where interrupt vectors are _not_ remapped,
+	# and reside in flash instead).
+	#
+	# See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
+	# Bit Symbol Value Description Reset
+	# value
+	# 0 MAP Memory map control. 0
+	# 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
+	# 1 User mode. The on-chip Flash memory is mapped to address 0.
+	# 31:1 - Reserved. The value read from a reserved bit is not defined. NA
+	#
+	# http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
+
+	mww 0x400FC040 0x01
+}

tcl/target/lpc1768.cfg

@@ -47,18 +47,10 @@ set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME lpc2000 0x0 0x80000 0 0 $_TARGETNAME \
 	lpc1700 $_CCLK calc_checksum
 
-# Although rclk "appears to work", it turns out that this yields
-# 4MHz whereas the "correct" rate is CCLK/6, which is not what
-# you get with rclk.
-#
-# Also, crank down the frequency further as we're running of an
-# RC oscillator instead of crystal.
-#
-# Setting up XTAL in the reset-init sequence could be worth 
-# the effort if you need to program the flash which is pretty
-# big on these devices.
-#
-jtag_khz 100
+# Run with *real slow* clock by default since the
+# boot rom could have been playing with the PLL, so
+# we have no idea what clock the target is running at.
+jtag_khz 10
 
 $_TARGETNAME configure -event reset-init {
 	# Do not remap 0x0000-0x0020 to anything but the flash (i.e. select