104 lines
2.6 KiB
INI
104 lines
2.6 KiB
INI
|
# script for stm32g4x family
|
||
|
|
|
||
|
|
#
|
||
|
|
# stm32g4 devices support both JTAG and SWD transports.
|
||
|
|
#
|
||
|
|
source [find target/swj-dp.tcl]
|
||
|
|
source [find mem_helper.tcl]
|
||
|
|
|
||
|
|
if { [info exists CHIPNAME] } {
|
||
|
|
set _CHIPNAME $CHIPNAME
|
||
|
|
} else {
|
||
|
|
set _CHIPNAME stm32g4x
|
||
|
|
}
|
||
|
|
|
||
|
|
set _ENDIAN little
|
||
|
|
|
||
|
|
# Work-area is a space in RAM used for flash programming
|
||
|
|
# Smallest current target has 32kB ram, use 16kB by default to avoid surprises
|
||
|
|
if { [info exists WORKAREASIZE] } {
|
||
|
|
set _WORKAREASIZE $WORKAREASIZE
|
||
|
|
} else {
|
||
|
|
set _WORKAREASIZE 0x4000
|
||
|
|
}
|
||
|
|
|
||
|
|
#jtag scan chain
|
||
|
|
if { [info exists CPUTAPID] } {
|
||
|
|
set _CPUTAPID $CPUTAPID
|
||
|
|
} else {
|
||
|
|
if { [using_jtag] } {
|
||
|
|
# See STM Document RM0440
|
||
|
|
# Section 46.6.3 - corresponds to Cortex-M4 r0p1
|
||
|
|
set _CPUTAPID 0x4ba00477
|
||
|
|
} {
|
||
|
|
set _CPUTAPID 0x2ba01477
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
|
||
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
||
|
|
|
||
|
|
if {[using_jtag]} {
|
||
|
|
jtag newtap $_CHIPNAME bs -irlen 5
|
||
|
|
}
|
||
|
|
|
||
|
|
set _TARGETNAME $_CHIPNAME.cpu
|
||
|
|
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
|
||
|
|
|
||
|
|
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
|
||
|
|
|
||
|
|
set _FLASHNAME $_CHIPNAME.flash
|
||
|
|
flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
|
||
|
|
|
||
|
|
if { [info exists QUADSPI] && $QUADSPI } {
|
||
|
|
set a [llength [flash list]]
|
||
|
|
set _QSPINAME $_CHIPNAME.qspi
|
||
|
|
flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
|
||
|
|
}
|
||
|
|
|
||
|
|
# reasonable default
|
||
|
|
adapter speed 2000
|
||
|
|
|
||
|
|
adapter srst delay 100
|
||
|
|
if {[using_jtag]} {
|
||
|
|
jtag_ntrst_delay 100
|
||
|
|
}
|
||
|
|
|
||
|
|
reset_config srst_nogate
|
||
|
|
|
||
|
|
if {![using_hla]} {
|
||
|
|
# if srst is not fitted use SYSRESETREQ to
|
||
|
|
# perform a soft reset
|
||
|
|
cortex_m reset_config sysresetreq
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event reset-init {
|
||
|
|
# CPU comes out of reset with HSION | HSIRDY.
|
||
|
|
# Use HSI 16 MHz clock, compliant even with VOS == 2.
|
||
|
|
# 1 WS compliant with VOS == 2 and 16 MHz.
|
||
|
|
mmw 0x40022000 0x00000001 0x0000000E ;# FLASH_ACR: Latency = 1
|
||
|
|
mmw 0x40021000 0x00000100 0x00000000 ;# RCC_CR |= HSION
|
||
|
|
mmw 0x40021008 0x00000001 0x00000002 ;# RCC_CFGR: SW=HSI16
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event reset-start {
|
||
|
|
# Reset clock is HSI (16 MHz)
|
||
|
|
adapter speed 2000
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event examine-end {
|
||
|
|
# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
|
||
|
|
mmw 0xE0042004 0x00000007 0
|
||
|
|
|
||
|
|
# Stop watchdog counters during halt
|
||
|
|
# DBGMCU_APB1_FZR1 |= DBG_IWDG_STOP | DBG_WWDG_STOP
|
||
|
|
mmw 0xE0042008 0x00001800 0
|
||
|
|
}
|
||
|
|
|
||
|
|
$_TARGETNAME configure -event trace-config {
|
||
|
|
# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
|
||
|
|
# change this value accordingly to configure trace pins
|
||
|
|
# assignment
|
||
|
|
mmw 0xE0042004 0x00000020 0
|
||
|
|
}
|