63 lines
1.5 KiB
INI
63 lines
1.5 KiB
INI
|
# SPDX-License-Identifier: GPL-2.0-or-later
|
||
|
|
|
||
|
|
# The Broadcom BCM2711 used in Raspberry Pi 4
|
||
|
|
# No documentation was found on Broadcom website
|
||
|
|
|
||
|
|
# Partial information is available in raspberry pi website:
|
||
|
|
# https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711/
|
||
|
|
|
||
|
|
if { [info exists CHIPNAME] } {
|
||
|
|
set _CHIPNAME $CHIPNAME
|
||
|
|
} else {
|
||
|
|
set _CHIPNAME bcm2711
|
||
|
|
}
|
||
|
|
|
||
|
|
if { [info exists CHIPCORES] } {
|
||
|
|
set _cores $CHIPCORES
|
||
|
|
} else {
|
||
|
|
set _cores 4
|
||
|
|
}
|
||
|
|
|
||
|
|
if { [info exists USE_SMP] } {
|
||
|
|
set _USE_SMP $USE_SMP
|
||
|
|
} else {
|
||
|
|
set _USE_SMP 0
|
||
|
|
}
|
||
|
|
|
||
|
|
if { [info exists DAP_TAPID] } {
|
||
|
|
set _DAP_TAPID $DAP_TAPID
|
||
|
|
} else {
|
||
|
|
set _DAP_TAPID 0x4ba00477
|
||
|
|
}
|
||
|
|
|
||
|
|
jtag newtap $_CHIPNAME cpu -expected-id $_DAP_TAPID -irlen 4
|
||
|
|
adapter speed 4000
|
||
|
|
|
||
|
|
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
|
||
|
|
|
||
|
|
# MEM-AP for direct access
|
||
|
|
target create $_CHIPNAME.ap mem_ap -dap $_CHIPNAME.dap -ap-num 0
|
||
|
|
|
||
|
|
# these addresses are obtained from the ROM table via 'dap info 0' command
|
||
|
|
set _DBGBASE {0x80410000 0x80510000 0x80610000 0x80710000}
|
||
|
|
set _CTIBASE {0x80420000 0x80520000 0x80620000 0x80720000}
|
||
|
|
|
||
|
|
set _smp_command "target smp"
|
||
|
|
|
||
|
|
for { set _core 0 } { $_core < $_cores } { incr _core } {
|
||
|
|
set _CTINAME $_CHIPNAME.cti$_core
|
||
|
|
set _TARGETNAME $_CHIPNAME.cpu$_core
|
||
|
|
|
||
|
|
cti create $_CTINAME -dap $_CHIPNAME.dap -ap-num 0 -baseaddr [lindex $_CTIBASE $_core]
|
||
|
|
target create $_TARGETNAME aarch64 -dap $_CHIPNAME.dap -ap-num 0 -dbgbase [lindex $_DBGBASE $_core] -cti $_CTINAME
|
||
|
|
|
||
|
|
set _smp_command "$_smp_command $_TARGETNAME"
|
||
|
|
}
|
||
|
|
|
||
|
|
if {$_USE_SMP} {
|
||
|
|
eval $_smp_command
|
||
|
|
}
|
||
|
|
|
||
|
|
# default target is cpu0
|
||
|
|
targets $_CHIPNAME.cpu0
|