riscv-openocd/tcl/board/mini2440.cfg

#-------------------------------------------------------------------------
# Mini2440 Samsung s3c2440A Processor with 64MB DRAM, 64MB NAND, 2 MB N0R
# NOTE: Configured for NAND boot (switch S2 in NANDBOOT)
# 64 MB NAND (Samsung K9D1208V0M)
# B Findlay  08/09
#
#   ----------- Important notes to help you on your way ----------
# README:
#     NOR/NAND Boot Switch - I have not read the vivi source, but from
#     what I could tell from reading the registers it appears that vivi
#     loads itself into DRAM and then flips NFCONT (0x4E000004) bits
#     Mode (bit 0 = 1), and REG_nCE (bit 1 = 0) which maps the NAND
#     FLASH at the bottom 64MB of memory. This essentially takes the
#     NOR Flash out of the circuit so you can't trash it.
#
#     I adapted the samsung_s3c2440.cfg file which is why I did not
#     include "source [find target/samsung_s3c2440.cfg]".  I believe
#     the -work-area-phys 0x200000 is incorrect, but also had to pad
#     some additional resets.  I didn't modify it as if it is working
#     for someone, the work-area-phys is not used by most.
#
#     JTAG ADAPTER SPECIFIC
#     IMPORTANT! Any JTAG device that uses ADAPTIVE CLOCKING will likely
#     FAIL as the pin RTCK on the mini2440 10 pin JTAG Conn doesn't exist.
#     This is Pin 11 (RTCK) on 20 pin JTAG connector. Therefore it is
#     necessary to FORCE setting the clock. Normally this should be configured
#     in the openocd.cfg file, but was placed here as it can be a tough
#     problem to figure out.  THIS MAY NOT FIX YOUR PROBLEM.. I modified
#     the openOCD driver jlink.c and posted it here. It may eventually end
#     up changed in openOCD, but its a hack in the driver and really should
#     be in the jtag layer (core.c me thinks), but haven't done it yet. My
#     hack for jlink.c may be found here.
#
#     http://forum.sparkfun.com/viewtopic.php?t=16763&sid=946e65abdd3bab39cc7d90dee33ff135
#
#     Note: Also if you have a USB JTAG, you will need the USB library installed
#     on your system "libusb-dev" or the make of openocd will fail. I *think*
#     it's apt-get install libusb-dev.  When I made my config I only included
#     --enable-jlink and --enable-usbdevs
#
#     I HAVE NOT Tested this throughly, so there could still be problems.
#     But it should get you way ahead of the game from where I started.
#     If you find problems (and fixes) please post them to
#     openocd-development@lists.berlios.de and join the developers and
#     check in fixes to this and anything else you find.  I do not
#     provide support, but if you ask really nice and I see anything
#     obvious I will tell you.. mostly just dig, fix, and submit to openocd.
#
#     best!   brfindla@yahoo.com   Nashua, NH USA
#
#     Recommended resources:
#       - first two are the best Mini2440 resources anywhere
#       - maintained by buserror... thanks guy!
#
#       http://bliterness.blogspot.com/
#       http://code.google.com/p/mini2440/
#
#       others....
#
#       http://forum.sparkfun.com/viewforum.php?f=18
#       http://labs.kernelconcepts.de/Publications/Micro24401/
#       http://www.friendlyarm.net/home
#       http://www.amontec.com/jtag_pinout.shtml
#
#-------------------------------------------------------------------------
#
#
# Your openocd.cfg file should contain:
# source [find interface/<yourjtag>.cfg]
# source [find board/mini2440.cfg]
#
#
#

# FIXME use some standard target config, maybe create one from this
#
#	source [find target/...cfg]

#-------------------------------------------------------------------------
# Target configuration for the Samsung 2440 system on chip
# Tested on a S3C2440 Evaluation board by keesj
# Processor : ARM920Tid(wb) rev 0 (v4l)
# Info: JTAG tap: s3c2440.cpu tap/device found: 0x0032409d
#  (Manufacturer: 0x04e, Part: 0x0324, Version: 0x0)
#-------------------------------------------------------------------------

if { [info exists CHIPNAME] } {
   set  _CHIPNAME $CHIPNAME
} else {
   set  _CHIPNAME s3c2440
}

if { [info exists ENDIAN] } {
   set  _ENDIAN $ENDIAN
} else {
  # this defaults to a bigendian
   set  _ENDIAN little
}

if { [info exists CPUTAPID ] } {
   set _CPUTAPID $CPUTAPID
} else {
  # force an error till we get a good number
   set _CPUTAPID 0x0032409d
}

#jtag scan chain
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position $_TARGETNAME
$_TARGETNAME configure -work-area-phys 0x40000000  -work-area-size 0x4000 -work-area-backup 1

#reset configuration
jtag_nsrst_delay 100
jtag_ntrst_delay 100
reset_config trst_and_srst

#-------------------------------------------------------------------------
# JTAG ADAPTER SPECIFIC
# IMPORTANT! See README at top of this file.
#-------------------------------------------------------------------------

    jtag_khz 12000
    jtag interface

#-------------------------------------------------------------------------
# GDB Setup
#-------------------------------------------------------------------------

    gdb_breakpoint_override hard

#------------------------------------------------
# ARM SPECIFIC
#------------------------------------------------

    targets
  #  arm7_9 dcc_downloads enable
  #  arm7_9 fast_memory_access enable


    nand device s3c2440 0

    jtag_nsrst_delay 100
    jtag_ntrst_delay 100
    reset_config trst_and_srst
    init

    echo " "
    echo "-------------------------------------------"
    echo "--- login with - telnet localhost 4444  ---"
    echo "--- then type help_2440                 ---"
    echo "-------------------------------------------"
    echo " "



#------------------------------------------------
# Processor Initialialization
# Note: Processor writes can only occur when
# the state is in SYSTEM. When you call init_2440
# one of the first lines will tell you what state
# you are in. If a linux image is booting
# when you run this, it will not work
# a vivi boot loader will run with this just
# fine. The reg values were obtained by a combination
# of figuring them out fromt the manual, and looking
# at post vivi values with the debugger. Don't
# place too much faith in them, but seem to work.
#------------------------------------------------

proc init_2440 { } {

    halt
    s3c2440.cpu curstate

    #-----------------------------------------------
    # Set Processor Clocks - mini2440 xtal=12mHz
    # we set main clock for 405mHZ
    # we set the USB Clock for 48mHz
    # OM2 OM3 pulled to ground so main clock and
    # usb clock are off 12mHz xtal
    #-----------------------------------------------

    mww phys 0x4C000014 0x00000005 #  Clock Divider control Reg
    mww phys 0x4C000000 0xFFFFFFFF #  LOCKTIME count register
    mww phys 0x4C000008 0x00038022 #  UPPLCON  USB clock config Reg
    mww phys 0x4C000004 0x0007F021 #  MPPLCON  Proc clock config Reg

    #-----------------------------------------------
    # Configure Memory controller
    # BWSCON configures all banks, NAND, NOR, DRAM
    # DRAM - 64MB - 32 bit bus, uses BANKCON6 BANKCON7
    #-----------------------------------------------

    mww phys 0x48000000 0x22111112 #  BWSCON - Bank and Bus Width
    mww phys 0x48000010 0x00001112 #  BANKCON4 - ?
    mww phys 0x4800001c 0x00018009 #  BANKCON6 - DRAM
    mww phys 0x48000020 0x00018009 #  BANKCON7 - DRAM
    mww phys 0x48000024 0x008E04EB #  REFRESH  - DRAM
    mww phys 0x48000028 0x000000B2 #  BANKSIZE - DRAM
    mww phys 0x4800002C 0x00000030 #  MRSRB6 - DRAM
    mww phys 0x48000030 0x00000030 #  MRSRB7 - DRAM

    #-----------------------------------------------
    # Now port configuration for enables for memory
    # and other stuff.
    #-----------------------------------------------

    mww phys 0x56000000	0x007FFFFF #  GPACON

    mww phys 0x56000010	0x00295559 #  GPBCON
    mww phys 0x56000018	0x000003FF #  GPBUP (PULLUP ENABLE)
    mww phys 0x56000014	0x000007C2 #  GPBDAT

    mww phys 0x56000020	0xAAAAA6AA #  GPCCON
    mww phys 0x56000028	0x0000FFFF #  GPCUP
    mww phys 0x56000024	0x00000020 #  GPCDAT

    mww phys 0x56000030	0xAAAAAAAA #  GPDCON
    mww phys 0x56000038	0x0000FFFF #  GPDUP

    mww phys 0x56000040	0xAAAAAAAA #  GPECON
    mww phys 0x56000048	0x0000FFFF #  GPEUP

    mww phys 0x56000050	0x00001555 #  GPFCON
    mww phys 0x56000058	0x0000007F #  GPFUP
    mww phys 0x56000054	0x00000000 #  GPFDAT

    mww phys 0x56000060	0x00150114 #  GPGCON
    mww phys 0x56000068	0x0000007F #  GPGUP

    mww phys 0x56000070	0x0015AAAA #  GPHCON
    mww phys 0x56000078	0x000003FF #  GPGUP

}



proc flash_config { } {

    #-----------------------------------------
    # Finish Flash Configuration
    #-----------------------------------------

    halt

    #flash configuration (K9D1208V0M: 512Mbit, x8, 3.3V, Mode: Normal, 1st gen)
    nand probe 0
    nand list
}

proc flash_uboot { } {

	# flash the u-Boot binary and reboot into it
	init_2440
	flash_config
	nand erase 0 0x0 0x40000
	nand write 0 /tftpboot/u-boot-nand512.bin 0 oob_softecc_kw
	resume
}


proc load_uboot { } {
        echo " "
        echo " "
        echo "----------------------------------------------------------"
        echo "---- Load U-Boot into RAM and execute it.              ---"
        echo "---- NOTE: loads, partially runs, and hangs            ---"
        echo "---- U-Boot is fine, this image runs from vivi.        ---"
        echo "---- I burned u-boot into NAND so I didn't finish      ---"
        echo "---- debugging it. I am leaving this here as it is     ---"
        echo "---- part of the way there if you want to fix it.      ---"
        echo "----                                                   ---"
        echo "---- mini2440 U-boot here:                             ---"
        echo "---- http://repo.or.cz/w/u-boot-openmoko/mini2440.git  ---"
        echo "---- Also this:                                        ---"
        echo "---- http://code.google.com/p/mini2440/wiki/MiniBringup --"
        echo "----------------------------------------------------------"

	init_2440
	echo "Loading /tftpboot/u-boot-nand512.bin"
	load_image /tftpboot/u-boot-nand512.bin 0x33f80000 bin
	echo "Verifying image...."
	verify_image /tftpboot/u-boot-nand512.bin 0x33f80000 bin
	echo "jumping to u-boot"
        #bp 0x33f80068 4 hw
        reg 0 0
        reg 1 0
        reg 2 0
        reg 3 0
        reg 4 0x33f80000
      	resume 0x33f80000
}

       # this may help a little bit debugging the load_uboot
proc s {} {
        step
        reg
        arm disassemble 0x33F80068 0x10
}

proc help_2440 {} {
    echo " "
    echo " "
    echo "-----------------------------------------------------------"
    echo "---- The following mini2440 funcs are supported        ----"
    echo "----   init_2440 - initialize clocks, DRAM, IO         ----"
    echo "----   flash_config - configures nand flash            ----"
    echo "----   load_uboot - loads uboot into ram               ----"
    echo "----   flash_uboot - flashes uboot to nand (untested)  ----"
    echo "----   help_2440 - this help display                   ----"
    echo "-----------------------------------------------------------"
    echo " "
    echo " "
}


#----------------------------------------------------------------------------
#----------------------------------- END ------------------------------------
#----------------------------------------------------------------------------