riscv-openocd/tcl/target/rp2040.cfg

# SPDX-License-Identifier: GPL-2.0-or-later

# RP2040 is a microcontroller with dual Cortex-M0+ core.
# https://www.raspberrypi.com/documentation/microcontrollers/rp2040.html

# The device requires multidrop SWD for debug.
transport select swd

source [find target/swj-dp.tcl]

if { [info exists CHIPNAME] } {
	set _CHIPNAME $CHIPNAME
} else {
	set _CHIPNAME rp2040
}

if { [info exists WORKAREASIZE] } {
	set _WORKAREASIZE $WORKAREASIZE
} else {
	set _WORKAREASIZE 0x10000
}

if { [info exists CPUTAPID] } {
	set _CPUTAPID $CPUTAPID
} else {
	set _CPUTAPID 0x01002927
}

# Set to '0' or '1' for single core configuration, 'SMP' for -rtos hwthread
# handling of both cores, anything else for isolated debugging of both cores
if { [info exists USE_CORE] } {
	set _USE_CORE $USE_CORE
} else {
	set _USE_CORE SMP
}
set _BOTH_CORES [expr { $_USE_CORE != 0 && $_USE_CORE != 1 }]

swj_newdap $_CHIPNAME cpu -expected-id $_CPUTAPID

# core 0
if { $_USE_CORE != 1 } {
	dap create $_CHIPNAME.dap0 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 0
	set _TARGETNAME_0 $_CHIPNAME.core0
	target create $_TARGETNAME_0 cortex_m -dap $_CHIPNAME.dap0 -coreid 0
	# srst does not exist; use SYSRESETREQ to perform a soft reset
	$_TARGETNAME_0 cortex_m reset_config sysresetreq
}

# core 1
if { $_USE_CORE != 0 } {
	dap create $_CHIPNAME.dap1 -chain-position $_CHIPNAME.cpu -dp-id $_CPUTAPID -instance-id 1
	set _TARGETNAME_1 $_CHIPNAME.core1
	target create $_TARGETNAME_1 cortex_m -dap $_CHIPNAME.dap1 -coreid 1
	$_TARGETNAME_1 cortex_m reset_config sysresetreq
}

if {[string compare $_USE_CORE SMP] == 0} {
	$_TARGETNAME_0 configure  -rtos hwthread
	$_TARGETNAME_1 configure  -rtos hwthread
	target smp $_TARGETNAME_0 $_TARGETNAME_1
}

if { $_USE_CORE == 1 } {
	set _FLASH_TARGET $_TARGETNAME_1
} else {
	set _FLASH_TARGET $_TARGETNAME_0
}
# Backup the work area. The flash probe runs an algorithm on the target CPU.
# The flash is probed during gdb connect if gdb_memory_map is enabled (by default).
$_FLASH_TARGET configure -work-area-phys 0x20010000 -work-area-size $_WORKAREASIZE -work-area-backup 1
set _FLASHNAME $_CHIPNAME.flash
flash bank $_FLASHNAME rp2040_flash 0x10000000 0 0 0 $_FLASH_TARGET

if { $_BOTH_CORES } {
	# Alias to ensure gdb connecting to core 1 gets the correct memory map
	flash bank $_CHIPNAME.alias virtual 0x10000000 0 0 0 $_TARGETNAME_1 $_FLASHNAME

	# Select core 0
	targets $_TARGETNAME_0
}