riscv-openocd/tcl/board/stm32f769i-disco.cfg

# SPDX-License-Identifier: GPL-2.0-or-later

# This is an STM32F769I discovery board with a single STM32F769NIH6 chip.
# http://www.st.com/en/evaluation-tools/32f769idiscovery.html

# This is for using the onboard STLINK
source [find interface/stlink.cfg]

transport select hla_swd

# increase working area to 256KB
set WORKAREASIZE 0x40000

# enable stmqspi
set QUADSPI 1

source [find target/stm32f7x.cfg]

reset_config srst_only

# QUADSPI initialization
proc qspi_init { } {
	global a
	mmw 0x40023830 0x000007FF 0				;# RCC_AHB1ENR |= GPIOAEN-GPIOKEN (enable clocks)
	mmw 0x40023838 0x00000002 0				;# RCC_AHB3ENR |= QSPIEN (enable clock)
	sleep 1									;# Wait for clock startup

	# PB02: CLK, PB06: BK1_NCS, PD13: BK1_IO3, PE02: BK1_IO2, PC10: BK1_IO1, PC09: BK1_IO0

	# PB06:AF10:V, PB02:AF09:V, PC10:AF09:V, PC09:AF09:V, PD13:AF09:V, PE02:AF09:V

	# Port B: PB06:AF10:V, PB02:AF09:V
	mmw 0x40020400 0x00002020 0x00001010	;# MODER
	mmw 0x40020408 0x00003030 0x00000000	;# OSPEEDR
	mmw 0x40020420 0x0A000900 0x05000600	;# AFRL

	# Port C: PC10:AF09:V, PC09:AF09:V
	mmw 0x40020800 0x00280000 0x00140000	;# MODER
	mmw 0x40020808 0x003C0000 0x00000000	;# OSPEEDR
	mmw 0x40020824 0x00000990 0x00000660	;# AFRH

	# Port D: PD13:AF09:V
	mmw 0x40020C00 0x08000000 0x04000000	;# MODER
	mmw 0x40020C08 0x0C000000 0x00000000	;# OSPEEDR
	mmw 0x40020C24 0x00900000 0x00600000	;# AFRH

	# Port E: PE02:AF09:V
	mmw 0x40021000 0x00000020 0x00000010	;# MODER
	mmw 0x40021008 0x00000030 0x00000000	;# OSPEEDR
	mmw 0x40021020 0x00000900 0x00000600	;# AFRL

	mww 0xA0001030 0x00001000				;# QUADSPI_LPTR: deactivate CS after 4096 clocks when FIFO is full
	mww 0xA0001000 0x03500008				;# QUADSPI_CR: PRESCALER=3, APMS=1, FTHRES=0, FSEL=0, DFM=0, SSHIFT=0, TCEN=1
	mww 0xA0001004 0x00190100				;# QUADSPI_DCR: FSIZE=0x19, CSHT=0x01, CKMODE=0
	mmw 0xA0001000 0x00000001 0				;# QUADSPI_CR: EN=1

	# exit qpi mode
	mww 0xA0001014 0x000033f5				;# QUADSPI_CCR: FMODE=0x0, DMODE=0x0, DCYC=0x0, ADSIZE=0x0, ADMODE=0x0, IMODE=0x3, INSTR=RSTQIO

	# 1-line memory-mapped read mode with 4-byte addresses
	mww 0xA0001014 0x0D003513				;# QUADSPI_CCR: FMODE=0x3, DMODE=0x1, DCYC=0x0, ADSIZE=0x3, ADMODE=0x1, IMODE=0x1, INSTR=READ

	# 4-line qpi mode
	mww 0xA0001014 0x00003135				;# QUADSPI_CCR: FMODE=0x0, DMODE=0x0, DCYC=0x0, ADSIZE=0x3, ADMODE=0x1, IMODE=0x1, INSTR=EQIO

	# 4-line memory-mapped read mode with 4-byte addresses
	mww 0xA0001014 0x0F283FEC				;# QUADSPI_CCR: FMODE=0x3, DMODE=0x1, DCYC=0xA, ADSIZE=0x3, ADMODE=0x1, IMODE=0x1, INSTR=4READ4B
}

$_TARGETNAME configure -event reset-init {
	mww 0x40023C00 0x00000006				;# 6 WS for 192 MHz HCLK
	sleep 1
	mww 0x40023804 0x24003008				;# 192 MHz: PLLM=8, PLLN=192, PLLP=2
	mww 0x40023808 0x00009400				;# APB1: /4, APB2: /2
	mmw 0x40023800 0x01000000 0x00000000	;# PLL on
	sleep 1
	mmw 0x40023808 0x00000002 0x00000000	;# switch to PLL
	sleep 1

	adapter speed 4000

	qspi_init
}