75 lines
2.1 KiB
INI
75 lines
2.1 KiB
INI
|
# DM6446 EVM board
|
||
|
|
# http://focus.ti.com/docs/toolsw/folders/print/tmdsevm6446.html
|
||
|
|
# http://c6000.spectrumdigital.com/davincievm/
|
||
|
|
# EVM is just the board; buy that at Spectrum.
|
||
|
|
# The "kit" from TI also has: video camera, LCD video monitor, more.
|
||
|
|
|
||
|
|
source [find target/ti_dm6446.cfg]
|
||
|
|
|
||
|
|
# J4 controls what CS2 hooks up to, usually NOR or NAND flash.
|
||
|
|
# S3.1/S3.2 controls boot mode, which may force J4 and S3.3 settings.
|
||
|
|
# S3.3 controls AEMIF bus width.
|
||
|
|
|
||
|
|
if { [info exists J4_OPTION] } {
|
||
|
|
# NOR, NAND, SRAM, ...
|
||
|
|
set CS2_MODE $J4_OPTION
|
||
|
|
} else {
|
||
|
|
set CS2_MODE ""
|
||
|
|
}
|
||
|
|
|
||
|
|
# ARM boot:
|
||
|
|
# S3.1 = 0, S3.2 = 0 ==> ROM/UBL boot via NAND (J4 == NAND)
|
||
|
|
# S3.1 = 1, S3.2 = 0 ==> AEMIF boot (J4 == NOR or SRAM)
|
||
|
|
# S3.1 = 0, S3.2 = 1 ==> ROM/UBL boot via HPI
|
||
|
|
# S3.1 = 1, S3.2 = 1 ==> ROM/UBL boot via UART (J4 == don't care)
|
||
|
|
# AEMIF bus width:
|
||
|
|
# S3.3 = 0 ==> 8 bit bus width
|
||
|
|
# S3.3 = 1 ==> 16 bit bus width
|
||
|
|
# DSP boot:
|
||
|
|
# S3.4 = 0 ==> controlled by ARM
|
||
|
|
|
||
|
|
if { $CS2_MODE == "NOR" } {
|
||
|
|
# 16 Mbytes address space; 16 bit bus width
|
||
|
|
# (older boards used 32MB parts, with upper 16 MB unusable)
|
||
|
|
flash bank cfi 0x02000000 0x01000000 2 2 $_TARGETNAME
|
||
|
|
proc flashprobe {} { flash probe 0 }
|
||
|
|
} elseif { $CS2_MODE == "NAND" } {
|
||
|
|
# 64 Mbyte small page; 8 bit bus width
|
||
|
|
nand device davinci $_TARGETNAME 0x02000000 hwecc1 0x01e00000
|
||
|
|
proc flashprobe {} { nand probe 0 }
|
||
|
|
} elseif { $CS2_MODE == "SRAM" } {
|
||
|
|
# 4 Mbyte address space; 16 bit bus width
|
||
|
|
# loaded via JTAG or HPI
|
||
|
|
proc flashprobe {} {}
|
||
|
|
} else {
|
||
|
|
# maybe it's HPI boot? can't tell...
|
||
|
|
echo "WARNING: CS2/flash configuration not recognized"
|
||
|
|
proc flashprobe {} {}
|
||
|
|
}
|
||
|
|
|
||
|
|
# NOTE: disable or replace this call to dm6446evm_init if you're
|
||
|
|
# debugging new UBL code from SRAM (for NAND boot).
|
||
|
|
$_TARGETNAME configure -event reset-init { dm6446evm_init }
|
||
|
|
|
||
|
|
#
|
||
|
|
# This post-reset init is called when the MMU isn't active, all IRQs
|
||
|
|
# are disabled, etc. It should do most of what a UBL does, except for
|
||
|
|
# loading code (like U-Boot) into DRAM and running it.
|
||
|
|
#
|
||
|
|
proc dm6446evm_init {} {
|
||
|
|
|
||
|
|
puts "Initialize DM6446 EVM board"
|
||
|
|
|
||
|
|
# FIXME initialize everything:
|
||
|
|
# - PLL1
|
||
|
|
# - PLL2
|
||
|
|
# - PINMUX
|
||
|
|
# - PSC
|
||
|
|
# - DDR
|
||
|
|
# - AEMIF
|
||
|
|
# - UART0
|
||
|
|
# - icache
|
||
|
|
|
||
|
|
flashprobe
|
||
|
|
}
|