interesting
/
riscv-openocd
mirror of https://github.com/riscv/riscv-openocd.git
1
0
Fork 0
Code Issues Projects Releases Wiki Activity
riscv-openocd/tcl/board/tp-link_tl-mr3020.cfg

13 lines
301 B
INI
Raw Normal View History

tcl/target|board: add config Atheros ar9331 Add configs for Atheros ar9331 MIPS based WiSoC and board based on this chip: TP-LINK TL-MR3020 Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/2519 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-01-30 06:05:31 -06:00
source [find target/atheros_ar9331.cfg]
tcl: replace $TARGETNAME with $_TARGETNAME code polishing to be consistent with other scripts Change-Id: Ib52a92f48df9d2bdf543792b856e33aa04dbebe3 Signed-off-by: Radek Dostal <radek.dostal@streamunlimited.com> Reviewed-on: http://openocd.zylin.com/2779 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-05-21 11:12:39 -05:00
$_TARGETNAME configure -event reset-init {
tcl/target|board: add config Atheros ar9331 Add configs for Atheros ar9331 MIPS based WiSoC and board based on this chip: TP-LINK TL-MR3020 Change-Id: I9e99719bce4bbb28311f6e9cddb32288db6e7b91 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/2519 Tested-by: jenkins Reviewed-by: Paul Fertser <fercerpav@gmail.com>
2015-01-30 06:05:31 -06:00
ar9331_25mhz_pll_init
sleep 1
ar9331_ddr1_init
}
set ram_boot_address 0xa0000000
tcl: replace $TARGETNAME with $_TARGETNAME code polishing to be consistent with other scripts Change-Id: Ib52a92f48df9d2bdf543792b856e33aa04dbebe3 Signed-off-by: Radek Dostal <radek.dostal@streamunlimited.com> Reviewed-on: http://openocd.zylin.com/2779 Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2015-05-21 11:12:39 -05:00
$_TARGETNAME configure -work-area-phys 0xa1FFE000 -work-area-size 0x1000
board: tp-link_tl-mr3020: add ath79 support Finally we can use this driver by default! Change-Id: I09d215d1bd1dc16873a7379637e6869af65ad8f1 Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4193 Tested-by: jenkins Reviewed-by: Dmytro <dioptimizer@hotmail.com> Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
2017-08-06 00:58:31 -05:00
flash: nor: ath79: remove base calculation Currently it is impossible to flash ELF with correct offsets. The reason is a bogus offset calculation extracted from base. Since any other spi drivers do not care about base, do the same for ath79 as well. Change-Id: I9e46e01c9e7a709c2d07da9203c634f302603afd Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Reviewed-on: http://openocd.zylin.com/4821 Tested-by: jenkins Reviewed-by: Tomas Vanek <vanekt@fbl.cz>
2018-12-26 05:47:11 -06:00
flash bank flash0 ath79 0xbf000000 0 0 0 $_TARGETNAME cs0