<p>The latest version in which the test is known to have passed is in the table below.</p>
<h2>Vocabulary</h2>
<tableborder="1">
<tr>
<tdwidth="100">Passed version</td>
<td>The latest branch and version on which the test is known to pass</td>
</tr>
<tr>
<tdwidth="100">Broken version</td>
<td>The latest branch and version on which the test is known to fail. n/a when older than passed version.</td>
</tr>
<tr>
<tdwidth="100">ID</td>
<td>A unqiue ID to refer to a test. The unique numbers are maintained in this file. Note that the same test can be run on different hardware/interface. Each combination yields a unique id. </td>
</tr>
</table>
<p></p>
<tableborder="1">
<tr>
<thwidth="100">Unique ID</th>
<thwidth="165">Synopsis</th>
<thalign="center"width="110">JTAG device</th>
<thalign="center"width="110">Passed version</th>
<thalign="center"width="110">Broken version</th>
</tr>
<tr>
<td>fill_malloc</td>
<tdwidth="165">Fill malloc() memory with garbage</td>
<p>Also new tests should be defined. Note that the code does not have to pass all the tests. In fact it can be helpful to have tests to describe facets that really should be working, but aren't done yet. </p>
Connect to ARM7 device(any), use GDB load to load a program into RAM and single halt, resume and single step.
<hr>
<h1>bdte-ram (Basic debugging test with Eclipse in RAM)<aid="bdte-ram"name="bdte-ram"></a></h1>
<p>This test was made under Eclipse with the Zylin Embedded CDT plugin. For the GDB "Initialize commands" take a look in the examples/<target>/prj/<b>eclipse_ram.gdb</b> file.</p>
<p>Start debugging, the debugger should stop at main. set some breakpoints and "Resume". If the debugger hit a breakpoint check if the "Variables" looks correct. Remove some breakpoints and "Resume" again. If the target is running, use the "Suspend" function and use "Step Into" or "Step Over" through the source. Even open the "Disassembly" view and enable the "Instruction Stepping Mode". Now you can single step through the assembler source. Use "Resume" again to run the program, set a breakpoint while the target is running. Check if you can inspect the variables with the mouse over. Play a little with the target...</p>
<hr>
<h1>bdte-rom (Basic debugging test with Eclipse in ROM)<aid="bdte-rom"name="bdte-rom"></a></h1>
<p>This test was made under Eclipse with the Zylin Embedded CDT plugin. For the GDB "Initialize commands" take a look in the examples/<target>/prj/<b>eclipse_rom.gdb</b> file.</p>
<p>Start debugging, the debugger should download and store the program in the flash of the target.</p>
<p>Now you can make some tests like described in the <ahref="#bdte-ram">bdte-ram</a> section above too.</p>
<p>For this test a STR710 with external memory was used. The example project can be found under examples/STR710JtagSpeed. Here Eclipse or the arm-elf-gdb can be used to download the test.elf file into the RAM. The result of the GDB can look like:</p>
<p>In this example a speed of 93 KB/sec was reached. The hardware which was used for the test can be found <ahref="http://www.yagarto.de/projects/str7usbmsd/index.html"target="new">here</a>.</p>
<p>The test was made on Windows XP Prof. (SP2) with a JTAGkey and the original FTDI driver.</p>
<p>For this test a STR710 with external memory was used. The example project can be found under examples/STR710JtagSpeed. Here Eclipse or the arm-elf-gdb can be used to download the test.elf file into the RAM. The result of the GDB can look like:</p>
<p>In this example a speed of 52 KB/sec was reached. The hardware which was used for the test can be found <ahref="http://www.yagarto.de/projects/str7usbmsd/index.html"target="new">here</a>.</p>
<p>The test was made on Mac OS X (10.5.2, Intel) with a JTAGkey and the following driver:</p>
