riscv-openocd/tcl/target/lpc8nxx.cfg

# NXP LPC8Nxx NHS31xx Cortex-M0+ with 8kB SRAM
# Copyright (C) 2018 by Jean-Christian de Rivaz
# Based on NXP proposal https://community.nxp.com/message/1011149
# Many thanks to Dries Moors from NXP support.
# SWD only transport

source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
	set  _CHIPNAME $CHIPNAME
} else {
	set  _CHIPNAME lpc8nxx
}

swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id 0
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian little -dap $_CHIPNAME.dap
if {![using_hla]} {
	# If srst is not fitted use SYSRESETREQ to  perform a soft reset
	cortex_m reset_config sysresetreq
}
adapter srst delay 100

$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x1ff0 -work-area-backup 0

flash bank $_CHIPNAME.flash lpc2000 0x0 0x7800 0 0 $_TARGETNAME lpc800 500

echo "*********************************************************************************"
echo "*         !!!!! IMPORTANT NOTICE FOR LPC8Nxx and NHS31xx CHIPS !!!!!"
echo "* When this IC is in power-off or peep power down mode, the SWD HW block is also"
echo "* unpowered. These modes can be entered by firmware. The default firmware image"
echo "* (flashed in production) makes use of this. Best is to avoid these power modes"
echo "* during development, and only later add them when the functionality is complete."
echo "* Hardware reset or NFC field are the only ways to connect in case the SWD is"
echo "* powered off. OpenOCD can do a hardware reset if you wire the adapter SRST"
echo "* signal to the chip RESETN pin and add the following in your configuration:"
echo "*     reset_config srst_only; flash init; catch init; reset"
echo "* But if the actual firmware immediately set the power down mode after reset,"
echo "* OpenOCD might be not fast enough to halt the CPU before the SWD lost power. In"
echo "* that case the only solution is to apply a NFC field to keep the SWD powered."
echo "*********************************************************************************"

# Using soft-reset 'reset_config none' is strongly discouraged.
# RESETN sets the system clock to 500 kHz. Unlike soft-reset does not.
# Set the system clock to 500 kHz before reset to simulate the functionality of hw reset.
#
proc set_sysclk_500khz {} {
	set SYSCLKCTRL 0x40048020
	set SYSCLKUEN 0x40048024
	mww $SYSCLKUEN 0
	mmw $SYSCLKCTRL 0x8 0xe
	mww $SYSCLKUEN 1
	echo "Notice: sysclock set to 500kHz."
}

# Do not remap the ARM interrupt vectors to anything but the beginning ot the flash.
# Table System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
# Bit Symbol  Value   Description
# 0   map         -   interrupt vector remap. 0 after boot.
#                 0   interrupt vector reside in Flash
#                 1   interrupt vector reside in SRAM
# 5:1 offset      -   system memory remap offset. 00000b after boot.
#            00000b   interrupt vectors in flash or remapped to SRAM but no offset
#            00001b -
#            00111b   interrupt vectors offset in flash or SRAM to 1K word segment
#            01000b -
#            11111b   interrupt vectors offset in flash to 1K word segment 8 to 31
# 31:6                reserved
#
proc set_no_remap {} {
	mww 0x40048000 0x00
	echo "Notice: interrupt vector set to no remap."
}

$_TARGETNAME configure -event reset-init {
	set_sysclk_500khz
	set_no_remap
}