This PR adds some hardening in the lower levels of the protocol stack, to bail early on invalid data. Primarily, attacks that this PR protects against are on the "annoyance"-level, which would otherwise write a couple of megabytes of data into the log output, which is a bit resource intensive.
This change
- implements concurrent LES request serving even for a single peer.
- replaces the request cost estimation method with a cost table based on
benchmarks which gives much more consistent results. Until now the
allowed number of light peers was just a guess which probably contributed
a lot to the fluctuating quality of available service. Everything related
to request cost is implemented in a single object, the 'cost tracker'. It
uses a fixed cost table with a global 'correction factor'. Benchmark code
is included and can be run at any time to adapt costs to low-level
implementation changes.
- reimplements flowcontrol.ClientManager in a cleaner and more efficient
way, with added capabilities: There is now control over bandwidth, which
allows using the flow control parameters for client prioritization.
Target utilization over 100 percent is now supported to model concurrent
request processing. Total serving bandwidth is reduced during block
processing to prevent database contention.
- implements an RPC API for the LES servers allowing server operators to
assign priority bandwidth to certain clients and change prioritized
status even while the client is connected. The new API is meant for
cases where server operators charge for LES using an off-protocol mechanism.
- adds a unit test for the new client manager.
- adds an end-to-end test using the network simulator that tests bandwidth
control functions through the new API.
Package p2p/enode provides a generalized representation of p2p nodes
which can contain arbitrary information in key/value pairs. It is also
the new home for the node database. The "v4" identity scheme is also
moved here from p2p/enr to remove the dependency on Ethereum crypto from
that package.
Record signature handling is changed significantly. The identity scheme
registry is removed and acceptable schemes must be passed to any method
that needs identity. This means records must now be validated explicitly
after decoding.
The enode API is designed to make signature handling easy and safe: most
APIs around the codebase work with enode.Node, which is a wrapper around
a valid record. Going from enr.Record to enode.Node requires a valid
signature.
* p2p/discover: port to p2p/enode
This ports the discovery code to the new node representation in
p2p/enode. The wire protocol is unchanged, this can be considered a
refactoring change. The Kademlia table can now deal with nodes using an
arbitrary identity scheme. This requires a few incompatible API changes:
- Table.Lookup is not available anymore. It used to take a public key
as argument because v4 protocol requires one. Its replacement is
LookupRandom.
- Table.Resolve takes *enode.Node instead of NodeID. This is also for
v4 protocol compatibility because nodes cannot be looked up by ID
alone.
- Types Node and NodeID are gone. Further commits in the series will be
fixes all over the the codebase to deal with those removals.
* p2p: port to p2p/enode and discovery changes
This adapts package p2p to the changes in p2p/discover. All uses of
discover.Node and discover.NodeID are replaced by their equivalents from
p2p/enode.
New API is added to retrieve the enode.Node instance of a peer. The
behavior of Server.Self with discovery disabled is improved. It now
tries much harder to report a working IP address, falling back to
127.0.0.1 if no suitable address can be determined through other means.
These changes were needed for tests of other packages later in the
series.
* p2p/simulations, p2p/testing: port to p2p/enode
No surprises here, mostly replacements of discover.Node, discover.NodeID
with their new equivalents. The 'interesting' API changes are:
- testing.ProtocolSession tracks complete nodes, not just their IDs.
- adapters.NodeConfig has a new method to create a complete node.
These changes were needed to make swarm tests work.
Note that the NodeID change makes the code incompatible with old
simulation snapshots.
* whisper/whisperv5, whisper/whisperv6: port to p2p/enode
This port was easy because whisper uses []byte for node IDs and
URL strings in the API.
* eth: port to p2p/enode
Again, easy to port because eth uses strings for node IDs and doesn't
care about node information in any way.
* les: port to p2p/enode
Apart from replacing discover.NodeID with enode.ID, most changes are in
the server pool code. It now deals with complete nodes instead
of (Pubkey, IP, Port) triples. The database format is unchanged for now,
but we should probably change it to use the node database later.
* node: port to p2p/enode
This change simply replaces discover.Node and discover.NodeID with their
new equivalents.
* swarm/network: port to p2p/enode
Swarm has its own node address representation, BzzAddr, containing both
an overlay address (the hash of a secp256k1 public key) and an underlay
address (enode:// URL).
There are no changes to the BzzAddr format in this commit, but certain
operations such as creating a BzzAddr from a node ID are now impossible
because node IDs aren't public keys anymore.
Most swarm-related changes in the series remove uses of
NewAddrFromNodeID, replacing it with NewAddr which takes a complete node
as argument. ToOverlayAddr is removed because we can just use the node
ID directly.
This commit affects p2p/discv5 "topic discovery" by running it on
the same UDP port where the old discovery works. This is realized
by giving an "unhandled" packet channel to the old v4 discovery
packet handler where all invalid packets are sent. These packets
are then processed by v5. v5 packets are always invalid when
interpreted by v4 and vice versa. This is ensured by adding one
to the first byte of the packet hash in v5 packets.
DiscoveryV5Bootnodes is also changed to point to new bootnodes
that are implementing the changed packet format with modified
hash. Existing and new v5 bootnodes are both running on different
ports ATM.
This PR implements the new LES protocol version extensions:
* new and more efficient Merkle proofs reply format (when replying to
a multiple Merkle proofs request, we just send a single set of trie
nodes containing all necessary nodes)
* BBT (BloomBitsTrie) works similarly to the existing CHT and contains
the bloombits search data to speed up log searches
* GetTxStatusMsg returns the inclusion position or the
pending/queued/unknown state of a transaction referenced by hash
* an optional signature of new block data (number/hash/td) can be
included in AnnounceMsg to provide an option for "very light
clients" (mobile/embedded devices) to skip expensive Ethash check
and accept multiple signatures of somewhat trusted servers (still a
lot better than trusting a single server completely and retrieving
everything through RPC). The new client mode is not implemented in
this PR, just the protocol extension.
Martin Holst Swende
Felföldi Zsolt
gary rong
Felix Lange
Péter Szilágyi
GagziW
Felix Lange